(No.52097)
DT-V1910CG
6
REAR/SIDE VIEW
<Rear Panel>
REMOTE (external control) terminals
T
erminals for controlling the monitor from an
external unit.
MAKE/TRIGGER terminal (Upper):
Enables the monitor to be controlled by closing the
circuit (point of contact) connected to the terminal.
RS-485IN terminal:
Enables the monitor to be controlled from a personal
computer via a serial cable.
RS-485 OUT terminal (Lower):
Enables a cascade control connection. Multiple moni-
tors can be controlled by the device connected to the IN
terminal.
Input card slots (SLOT 1 — SLOT 3)
Optional input cards can be installed in these
slots. Input cards are not provided when you
purchase the monitor
.
NOTE:
It is not possible to input video or audio signals to the monitor
when no input cards are installed.
Main power switch
Press the switch to turn the main power ON or
OFF
. When the main power is ON, the power
lamp on the front panel lights in yellow and the
monitor enters the stand-by mode.
•
I : ON
: OFF
G/Y
OUT
IN
OUT
IN
R/P
R
/B-Y
SLOT
1
SLOT
3
SLOT
2
MAIN PO
WER
OUT
IN
VD
OUT
IN
HD/C
S
OUT
IN
OUT
IN
A
U
DIO
OUT
IN
B/P
B
/B-Y
A
UDIO
OUT
IN
SWITCHED
OUT
HD SDI 1
HD SDI 2
IN
IN
22
23
24
MAKE/TRIGGER
REMO
T
E
21
RS-485
IN
OUT
25
<Side Panel>
21
22
23
24
25
AC inlet
Power input connector
. Connect the provided
AC
power cord to an
AC outlet (120 V/230 V
AC, 50
Hz/60 Hz).
*
Attach the provided Power Cord Holder to prevent
accidental disconnection of the
AC power cord.
Refer to page 10 for details.
Built-in speaker (monaural)
Outputs the selected INPUT audio signal.
CONTROLS AND FEA
TURES
(cont'd)
Power lamp
Unlit
:
The main power is OFF
.
Orange
:
The main power is ON, but the monitor
’s
power
is OFF (in stand-by mode).
Green
:
The main power is ON, and the monitor
’s
power is ON (in normal operation mode).
POWER switch
Press the power switch to turn the monitor
’s
power ON or OFF when the main power is ON.
NOTE:
When RUSH DELA
Y
TIME is set to SLOW in the set-up menu, it
takes approx. 3.2 seconds for the power to actually turn ON after
the power switch is pressed.
19
20
7
Component/RGB signal input/output terminals
Input (IN) and output (OUT) terminals for component (color dif
ference) or
RGB signals.
Select component signal
:
INPUT
SELECT
A
(SLOT1)/C (SLOT2)/E (SLOT3)
Select RGB signal
:
INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3)
*
The IN and OUT
terminals are bridge-connected (auto termination).
Synchronized signal input/output terminals
Input (IN) and output (OUT) terminals for the vertical, horizontal or complex
synchronized signals.
•
T
o use these terminals, set “SYNC SELECT” to “EXT”.
Refer to “SYNC SELECT” on page 17 for more information.
Audio input/output terminals
Input (IN) and output (OUT) terminals for the analog audio signals.
•
The IN and OUT terminals are bridge-connected.
Connection terminal
Attach to the connection terminal of your Multi-Format Monitor
.
1
CONTROLS AND FEA
TURES
(INPUT CARD: OPTIONAL)
COMPONENT/RGB INPUT CARD (IF-C01COMG)
Compatible signal formats:
NTSC (3.58 MHz), P
A
L
(4.43 MHz),
black-and-white
(50 Hz/60 Hz)
VIDEO INPUT CARD (IF-C01PNG)
Compatible signal formats:
480/60i, 576/50i, 576/50p, 480/60p, 720/
60p, 1035/60i, 1080/50i, 1080/60i, 1080/
24psF
Composite signal input/output terminals (VIDEO1, VIDEO2)
Input (IN) and output (OUT) terminals for the composite video signals of the
NTSC, P
AL, and black/white (50/60Hz).
NTSC and P
A
L
are switched in the “COLOR SYSTEM”. Refer to “COLOR
SYSTEM” on page 17.
Select VIDEO 1:
press INPUT
SELECT
A
(SLOT1)/C (SLOT2)/E (SLOT3) buttons.
Select VIDEO 2:
press INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3) buttons.
*
The IN and OUT terminals are bridge-connected (auto termination).
S-video signal input terminal (only for VIDEO 2)
Input terminal for the S-video signal.
• When an S-video signal is input to this terminal and a video signal is input to VIDEO
2, the S-video signal has priority over the video signal.
Synchronized signal input/output terminals (for both VIDEO
1 and VIDEO 2)
Input (IN) and output (OUT) terminals for the complex synchronized signals.
T
o
use these terminals, set “SYNC SELECT” to “EXT”. Refer to “SYNC
SELECT” on page 17 for more information.
NOTES:
• When an external synchronized signal is input, external synchronization is prioritized
for both VIDEO1 and VIDEO2.
• External synchronization does not function when a video signal (except black burst
signal) is included in the complex synchronized signal.
Audio signal input/output terminals (for both VIDEO 1 and
VIDEO 2)
Input (IN) and output (OUT) terminals for analog audio signals correspond-
ing to VIDEO 1 and VIDEO 2.
•
The IN and OUT terminals are bridge-connected.
Connection terminal
Attach to the connection terminal of your Multi-Format Monitor
.
1
2
3
4
2
3
4
5
B/P
B
/B-Y
G/Y
OUT
IN
OUT
IN
R/P
R
/B-Y
OUT
IN
VD
OUT
IN
HD/C
S
OUT
IN
OUT
IN
A
UDIO
OUT
IN
1
2
3
4
VIDEO 1
OUT
IN
A
UDIO 2
A
UDIO 1
OUT
IN
VIDEO 2
OUT
Y/C IN
IN
OUT
IN
EXT
.SYNC
1
2
3
4
5
