(No.52097)
DT-V1910CG
8
HD SDI INPUT CARD (IF-C12HSDG)
Compliant with EMBEDDED
AUDIO
Compatible signal formats: 720/60p,
1080/50i, 1080/60i,
1035/60i, 1080/24psF
, EMBEDDED
AUDIO
HD SDI signal input/output terminals (HD SDI 1, HD SDI 2)
Input (IN) and output (OUT) terminals for the HD SDI signal (HD compo-
nent serial digital signal)
This card is also compatible with EMBEDDED
AUDIO signals with a 48kHz
sampling frequency and channel range of 1-8.
The EMBEDDED
AUDIO output channel is controlled from this monitor
.
Refer to “EMBEDDED
AUDIO channel switch button” on page 4 for more
information.
Select HD SDI1 input
:
press INPUT
SELECT
A
(SLOT1)/C (SLOT2)/E (SLOT3)
buttons.
Select HD SDI2 input
:
press INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3)
buttons.
OUT terminal
The re-clocked HD SDI1 and/or HD SDI2 input signal is output from the HD
SDI1 OUT and/or HD SDI2 OUT terminal.
NOTE:
• Signals cannot be output from the OUT
terminal when the monitor
’s
power is OFF
or in the stand-by mode.
Connection terminal
Attach to the connection terminal of your Multi-Format Monitor
.
1
2
CONTROLS AND FEA
TURES
(INPUT CARD: OPTIONAL)
(cont'd)
SDI INPUT CARD (IF-C01SDG)
SWITCHED OUT terminal
Output (OUT) terminal for the re-clocked signal.
The input signal from SDI1
or SDI2 (selected with the INPUT SELECT buttons) is re-clocked and output
from this terminal.
NOTES:
• Even when the input signal is switched from the SDI Input Card, the SWITCHED
OUT terminal still outputs the SDI 1 or SDI 2 re-clocked signal (whichever you
selected last).
• No signal is output from the SWITCHED OUT terminal when the monitor is turned
of
f or in the stand-by mode.
D1 SDI signal input terminal (SDI1, SDI2)
Accepts an SMPTE259M compliant D1 SDI signal (component serial digital
signal).
Select SDI1 input:
press INPUT
SELECT
A
(SLOT1)/C (SLOT2)/E (SLOT3) buttons.
Select SDI2 input:
press INPUT SELECT B (SLOT1)/D (SLOT2)/F (SLOT3) buttons.
NOTE:
Not compliant with EMBEDDED
AUDIO.
Audio signal input/output terminals (for both SDI1 and SDI2)
Input (IN) and output (OUT) terminals for the analog audio signals.
•
The IN and OUT
terminals are bridge-connected.
Connection terminal
Attach to the connection terminal of your Multi-Format Monitor
.
1
Compatible signal formats: 480/60i,
576/50i
2
3
4
A
UDIO 2
A
UDIO 1
OUT
IN
SWITCHED
OUT
SDI 1
SDI 2
IN
IN
1
2
3
4
E.A
UDIO
HD SDI 1
IN
OUT
2
1
E.A
UDIO
HD SDI 2
IN
OUT
9
PREP
ARA
TION
1. T
u
rn off the Multi-Format Monitor
’s main
power and unplug the power cable from
the AC
outlet.
2. Unscrew the screws and remove the slot
cover from the slot (on the rear side of the
monitor) in which you are going to install
the card.
3.
Insert the Input Card’
s board (green-
colored) into the slot, fitting the board into
the guide rails on the top and bottom of
the slot.
4. Push the Input Card in so that its front
panel touches the monitor
’s rear panel.
5. Secure the Input Card by replacing the
screws removed in Procedure 2.
INST
ALLING THE INPUT
CARD
Optional input cards are necessary to use the functions of this
monitor
. Before mounting the monitor or connecting other
equipment to the monitor
, be sure to install the input cards.
SLOT1
SLOT3
SLOT2
MAKE/TRIGGER
REMO
TE
RS-485
IN
OUT
MAKE/TRIGGER
REMO
TE
RS-485
IN
OUT
SLOT1
SLOT3
SLOT2
SLOT1
SLOT3
SLOT2
MAKE/TRIGGER
REMO
TE
RS-485
IN
OUT
A
T
T
ACHING THE WIDE
MASK
A
wide mask is provided with the monitor
.
This changes the
viewable screen area to the 16:9 aspect ratio.
•
The wide mask cannot be attached to the monitor after the
monitor is mounted in a rack. Mount the wide mask before
installing the monitor in a rack.
1.
Prepare the provided wide mask and 4
screws (for attaching).
2.
Attach the wide mask to the monitor
.
3.
Secure the wide mask with the screws (fix
2 screws each to both right and left side).
●
When detaching the wide mask, follow this procedure in
reverse.
Slot cover
Fit the board to
the guide rails.
Knob
Guide rails
Knob
NOTES:
•
Do not touch the terminal connected to the monitor or board
pattern.
•
Do not remove slot covers from the monitor
’s
slots if they
are not in use.
Input card (the illustration
shown is of the IF-C01PNG)
Caution:
Use only the provided screws.
Rear side of the DT
-V1910CG
Multi-Format Monitor
