TABLE OF CONTENTS
Section
Title
Page
I
mportant Safety Precautions
DIFFERENT TABLE
1. DISASSEMBLY
1.3.2 Disassembly method ( I ) ............................................ 1-1
2. ELECTRICAL ADJUSTMENT
2.1
ELECTRICAL ADJUSTMENT .......................................... 2-1
2.1.1 Precautions ................................................................. 2-1
2.1.2 Test instruments required for electrical adjustment ............. 2-1
2.1.3 Required test equipment ............................................ 2-1
2.1.4 Setup (LCD ADJUSTMENT) ........................................ 2-1
2.1.5 Setup (CCD ADJUSTMENT) ....................................... 2-2
2.2
Setup with patch cords and jig connector cables ............ 2-3
3. CHARTS AND DIAGRAMS
NOTES OF SCHEMATIC DIAGRAM ........................................ 3-1
CIRCUIT BOARD NOTES ......................................................... 3-2
3.1
BOARD INTERCONNECTION ......................................... 3-3
3.2
MAIN (SYSCON) SCHEMATIC DIAGRAM ...................... 3-5
3.3
MAIN (DSP146) SCHEMATIC DIAGRAM ........................ 3-7
3.4
MAIN (DSP97) SCHEMATIC DIAGRAM .......................... 3-9
3.5
MAIN (CDS AGC A/D AND ARM ROM)
SCHEMATIC DIAGRAM ................... 3-11
3.6
MAIN (STROBE CONTROL AND AUDIO ) AND
STROBE FLASH SCHEMATIC DIAGRAMS ........ 3-12
3.7
MAIN (F/Z_MDA / IRIS) SCHEMATIC DIAGRAM ......... 3-13
3.8
JACK (VIDEO OUT/USB/PRINTER/DC JACK/
MONITOR BACK LIGHT) SCHEMATIC DIAGRAM .... 3-14
3.9
CCD SCHEMATIC DIAGRAM ........................................ 3-15
3.10 MONI REG (MONITOR) SCHEMATIC DIAGRAM ......... 3-16
3.11 MONITOR REG (DC/DC) SCHEMATIC DIAGRAM ........ 3-17
3.12 MAIN CIRCUIT BOARD (YB10299-01-01) ..................... 3-19
3.13 MAIN CIRCUIT BOARD (YB10299-01-03) ..................... 3-25
3.14 MONITOR REG CIRCUIT BOARD (YB10300-01-01) ..... 3-31
3.15 MONITOR REG CIRCUIT BOARD (YB10300-01-02) ..... 3-31
3.16 JACK CIRCUIT BOARD (YB10300-01-01) .................... 3-35
3.17 JACK CIRCUIT BOARD (YB10300-01-02) .................... 3-37
3.18 CCD CIRCUIT BOARD (YB10300-01-01) ...................... 3-39
3.19 CCD CIRCUIT BOARD (YB10300-01-02) ...................... 3-40
3.20 STOROBE FLASH CIRCUIT BOARD (YB10300-01-01) ... 3-41
3.21 STOROBE FLASH CIRCUIT BOARD (YB10300-01-02) ... 3-42
3.22 OVER ALL BLOCK DIAGRAM ....................................... 3-43
4. PARTS LIST
4.1
PACKING AND ACCESSORY ASSEMBLY <M1> ........... 4-1
4.3
FINAL ASSEMBLY <M2> .............................................. 4-3
4.4
ELECTRICAL PARTS LIST ............................................... 4-6
MAlN BOARD ASSEMBLY <01> .................................... 4-6
CCD BOARD ASSEMBLY <02> .................................... 4-11
MONI REG BOARD ASSEMBLY <03> ......................... 4-12
JACK BOARD ASSEMBLY <04> .................................. 4-14
STROBE FLASH BOARD ASSEMBLY <05> ................. 4-15
The following table indicate main different features between models GC-QX3U, GC-QX3HDU and GC-QX5HDU.
Shooting Continuous Photos
YES
NO
YES
Collage Mode
YES
NO
YES
6M Pro-Still(Pixel Shift Mode)
YES
NO
YES
DR Pro-Still(Wide Range Mode)
YES
NO
YES
Installing the Film Copying Adapter
NO
NO
YES
Shooting Film(Film Copy Mode)
NO
NO
YES
MODEL
GC-QX3U
GC-QX3HDU
ITEM
GC-QX5HDU
Operating Environment
The host computer that runs the Macintosh
®
operating environment must satisfy the following
conditions.
USB Driver
1. USB-compatible computer (iMac™, iBook™,
Power Mac™ G3/G4, Power Book™ G3, etc.)
2. Mac OS 8.5.1/Mac OS 8.6/Mac OS 9.0
JVC Video Decoder
1. Power PC 603e/120MHz or faster
2. Mac OS 7.6.1 or later
3. QuickTime 3.0 or later
4. Minimum RAM requirement: 32MB
5. Minimum hard disk space requirement: 1MB
* Macintosh
®
is a registered trademark of Apple
Computer.
* Other trademarks are property of their respective
owners.
* If you use Macintosh
®
which does not have a USB
port, use an optional flash path, conversion card
adapter, etc. For details on the operating environ-
ment of these devices, contact the dealers or
manufacturers.
SOFTW ARE SECTION FOR Macintosh
®
Operating Environment
SOFTW ARE SECTION FOR Windows
®
The host computer that runs the Windows
®
operating environment must satisfy the following
conditions.
USB Driver
1. Microsoft
®
Windows
®
98/Windows
®
98 Second
Edition, Full version (Not Upgrade)/Windows
®
2000 Professional (Not Upgrade)
2. Available USB port
3. CD-ROM drive
Video Player
1. CPU: Intel
®
Pentium
®
200MHz class or higher
2. Microsoft
®
Windows
®
95/Windows
®
98
3. Display capability of 65,536 colors or more
4. CD-ROM drive
5. Minimum RAM requirement: 32MB
6. Minimum hard disk space requirement: 1MB
* The system requirements information is not a
guarantee that provided software applications will
work on all personal computers meeting those
requirements.
* Microsoft
®
, Windows
®
are either registered
trademarks or trademarks of Microsoft corporation
in United States and/or other countries.
* Intel
®
, Pentium
®
are registered trademarks of Intel
corporation.
* Other trademarks are property of their respective
owners.
* If you use Windows
®
95 or a personal computer
which does not have a USB port, use an optional
flash path, conversion card adapter, etc. For
details on the operating environment of these
devices, contact the dealers or manufacturers.
