background image

58

 EN

Cassettes

To properly use and store your cassettes, be sure to
read the following cautions:
1. During use . . .

.... make sure the cassette bears the VHS-C

mark.

.... be aware that recording onto prerecorded

tapes automatically erases the previously
recorded video and audio signals.

.... make sure the cassette is positioned properly

when inserting.

.... do not load and unload the cassette

repeatedly without allowing the tape to run
at all. This slackens the tape and can result in
damage.

.... do not open the front tape cover. This

exposes the tape to fingerprints and dust.

2. Store cassettes . . .

.... away from heaters or other heat sources.
.... out of direct sunlight.
.... where they won’t be subject to unnecessary

shock or vibration.

.... where they won’t be exposed to strong

magnetic fields (such as those generated by
motors, transformers or magnets).

.... vertically, in their original cases.

Main Unit

1. For safety, DO NOT . . .

.... open the camcorder’s chassis.
.... disassemble or modify the unit.
.... short-circuit the terminals of the battery pack.

Keep it away from metallic objects when not
in use.

.... allow inflammables, water or metallic objects

to enter the unit.

.... remove the battery pack or disconnect the

power supply while the power is on.

.... leave the battery pack attached when the

camcorder is not in use.

2. Avoid using the unit . . .

.... in places subject to excessive humidity or

dust.

.... in places subject to soot or steam such as

near a cooking stove.

.... in places subject to excessive shock or

vibration.

.... near a television set.
.... near appliances generating strong magnetic

or electric fields (speakers, broadcasting
antennas, etc.).

.... in places subject to extremely high (over

40°C or 104°F) or extremely low (under 0°C
or 32°F) temperatures.

3. DO NOT leave the unit . . .

.... in places of over 50°C (122°F).
.... in places where humidity is extremely low.

(below 35%) or extremely high (above 80%).

.... in direct sunlight.
.... in a closed car in summer.
.... near a heater.

4. To protect the unit, DO NOT . . .

.... allow it to become wet.
.... drop the unit or strike it against hard objects.
.... subject it to shock or excessive vibration

during transportation.

.... keep the lens directed at extremely bright

objects for long periods.

.... direct the eyepiece of the viewfinder at the

sun.

.... carry it by holding the viewfinder. Be sure to

hold the main unit with both hands or use
the grip.

.... swing it excessively when using the shoulder

strap.

CAUTIONS 

 (cont.)

About moisture condensation . . .

You may have observed that pouring a cold
liquid into a glass will cause drops of water to
form on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool
place to a warm place, after heating a cold
room, under extremely humid conditions or
in a place directly subjected to the cool air
from an air conditioner.

Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit
immediately and consult your local JVC dealer.

Summary of Contents for GR-AX930

































































Reviews: