background image

16

 EN

RECORDING

  Basic Recording (cont.)

Shooting while watching the LCD monitor

Before the following steps, perform step 1 (

Z

 pg. 15).

ENTER RECORD–STANDBY MODE

2

Make sure the LCD monitor is fully open. Slide the
LENS COVER open/close switch to open the lens
cover, then set the power switch to CAMERA.

•The power indicator lights and the camcorder

enters the Record–Standby mode.

•The scene you’re aimed at appears in the LCD

monitor, with the word “PAUSE” superimposed
upon it.

START SHOOTING

3

Tilt the LCD monitor upward/downward for best
viewability (

Z

 pg. 17) and press the Recording

Start/Stop button.

•The tally lamp lights while recording is in progress,

and “

REC

” appears in the LCD monitor.

STOP RECORDING

4

Press the Recording Start/Stop button again to stop
recording.

•The camcorder re-enters the Record-Standby

mode.

NOTES:

When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, we recommend that you use the viewfinder
(

Z

 pg. 15).

For other notes, refer to pg. 15.

25MIN

120MIN

119MIN

3MIN

2MIN (Blinking)

1MIN (Blinking)

0MIN (Blinking)

*- - -MIN
(Now calculating)

LENS COVER
Switch

POWER

Start/Stop

Power indicator

Tape remaining time indicator

MONITOR
OPEN

Tally lamp

Summary of Contents for GR-AXM2

























































Reviews: