EN
53
NOTE:
Use the remote control unit to perform the following procedures.
Audio Dubbing
You can record a new soundtrack on a prerecorded
tape (normal audio only). The sound is recorded from
the built-in microphone.
Perform steps 1, 2 and 3 of the Insert Editing
(VIDEO) procedure (
pg. 52) before continuing.
NOTE:
Use the remote control unit to perform the following
procedures.
1
Press
REW
(
2
) to go a little beyond the
beginning of the scene onto which you want to
dub the new audio, press
PLAY
(
4
) to view the
recorded tape, then press
PAUSE
(
6
) at exactly
the point where dubbing should start.
2
Press and hold
A. DUB
(
e
), and without
releasing
A. DUB
(
e
), press and release
PAUSE
(
6
). The Audio Dub-Standby mode is engaged.
3
To begin Audio Dubbing, press
PLAY
(
4
). When
the counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode.
4
To end Audio Dubbing, press
STOP
(
5
).
NOTES:
●
Do not press
FF
(
3
)
or
REW
(
2
)
during Audio
Dub-Standby, or the edit points will not be
accurate.
●
If the microphone is too close to the TV, or if the
TV’s volume is too high, whistling or howling may
occur.
NOTES
(for Insert Editing and Audio Dubbing):
●
Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.
●
To edit/dub onto a tape, make sure the Erase
Protection tab is in the position that allows
recording. If not, slide the tab. Some cassettes have
removable tabs. If the tab has been removed, cover
the hole with adhesive tape.
●
Do not press
STOP
(
5
)
during Insert Editing or
Audio Dubbing, or the edit points will not be
accurate.
●
During Insert Editing and Audio Dubbing, when
Insert-Pause or Audio Dub-Standby is engaged, the
counter may go slightly past “0:00:00”. Recording,
however, stops at exactly 0:00:00.
Insert Editing (Insert A Still Image
From The Built-in Memory Onto A
Tape)
You can insert a still image stored in the camcorder’s
built-in memory into a previously recorded tape,
replacing a section of the original recording with
minimal picture distortion at the in- and out-points.
The original audio remains unchanged.
Perform steps 1 through 5 in Insert Editing (VIDEO)
(
pg. 52) before the following procedure.
1
Press
REFRESH
for approx. 1 second to select
“DSC”. The DSC Lamp comes on. Press
REW
(
2
) or
FF
(
3
) to select the still image you
wish to insert.
2
To begin Insert Editing, press
START/STOP
.
When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode.
To insert still images in sequential order onto
the tape . . .
... press
REW
(
2
)
or
FF
(
3
)
to move the
page forward.
To insert still images at random onto the
tape . . .
... first record the still image you selected in
step
1
onto the tape, then press
START/
STOP
to engage the Insert-Pause mode. To
select another still image, press
REW
(
2
)
or
FF
(
3
)
again, then press
START/STOP
.
Insert Editing begins.
3
To end Insert Editing, press
STOP
(
5
).
NOTES:
●
The tape may stop slightly before or after the
designated end point, and noise bars may appear.
Neither indicates a defect in the unit.
●
Only video signal is recorded in the Insert Editing
mode.
