EN
39
8
Set recording speed
Press
REC SPEED
to set the recording speed.
9
Return to normal screen
Press
@
#
to move the arrow to “CONFIRM”,
then press
OK
.
“PROGRAM COMPLETED PRESS [TIMER] TO
ENTER TIMER STANDBY MODE” appears on the
screen, then press
OK
to return to normal screen.
0
Engage timer recording standby mode
Press
TIMER (
‰
)
.
The VCR turns off automatically and “
‰
” is
displayed on the front display panel.
To timer-record daily or weekly serials
Press
DAILY
(number “
8
”) or
WEEKLY
(number “
9
”)
anytime during steps
4
through
8
.
“MON – FRI”, “MON – SAT”, “SUN – SAT” or
“EVERY _ _ _” appears on the Program screen.
●
Pressing the button again makes the corresponding
indication disappear.
To use the VCR while it is in timer recording standby
mode
Press
TIMER (
‰
)
to cancel the timer recording standby
mode, then press
POWER
to turn on the VCR.
DO NOT forget to put the VCR into timer recording
standby mode again by pressing
TIMER (
‰
)
after you
use the VCR; otherwise, you cannot record the broadcast
you want.
●
When “AUTO TIMER” (
墌
pg. 57) is set to “ON”, the
timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have
to press
TIMER (
‰
)
to engage or disengage the timer
recording standby mode.
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS
receiver (unless “INPUT
CH” is set to “OFF” on
DBS Receiver Set screen
墌
pg. 19), the band
indication (TV, CATV or
DBS) appears under the
channel number
indication (SOURCE).
TV
:To timer-record a regular TV broadcast
received on the VCR.
CATV :To timer-record a cable TV broadcast
received on the VCR, or through a cable box
(unless “INPUT CH” is set to “OFF” on
Cable Set Up screen
墌
pg. 16).
DBS
:To timer-record a satellite broadcast
received through a DBS receiver.
NOTE:
If “BAND” is set to “TV” on the Tuner Set Up Screen
(
墌
pg. 14) and “INPUT CH” is set to “OFF” on Cable Set
Up screen (
墌
pg. 16), “CATV” will not be displayed on the
Program screen; If “BAND” is set to “CATV” or “INPUT
CH” is set to “ON” on Cable Set Up screen, “TV” will not
be displayed.
If the channel number entered requires that the band
be set, “7=DBS” is displayed on the screen.
If this happens, press the
Number
key “
7 (DBS)
” to
select “DBS”.
NOTES:
●
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time is lost if it lasts for more
than 10 minutes.
As a result, when the power is supplied again to this VCR
after the power failure, the following will take place.
1. This VCR starts Auto Clock Set automatically to restore the
clock time.
2. If the clock time is restored correctly and “AUTO TIMER” is
set to “ON”, each timer program you have made will start
at its start time unless its end time has elapsed.
●
Programs that start after midnight must have the next day’s
date.
●
After timer recording is completed, the VCR turns off
automatically.
●
You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
●
If the tape reaches its end during timer recording, “
‰
”, “ ”,
and “
#
” blink.
●
To timer-record cable or satellite channels, be sure to keep
the cable box or DBS receiver turned on.
CONFIRM
CANCEL
10:00 PM
STD (SP)
110 CH
DBS
8:00 PM
START TIME
STOP TIME
DATE
DAILY/WEEKLY
CH
SOURCE
TIMER PROGRAM
REC SPEED
SET PROGRAM WITH [+/–, REC SPEED,7=DBS,
8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"
START STOP DATE
CH
EXIT
PROG.
12/24/03 (WED)
EVERY WED
HM-DH40000U-EN34-41
1/28/3, 10:07 AM
39
