1-14 (No.82933)
3- : Mechanism sensor information
[Common table of MN*, HD* and M3*]
-4 : Mechanism mode position
[Common table of MN*, HD* and M3*]
Note:
•
In the case of the “HD*” microprocessor, as the dis play
is always “-7” at any intermediate position between
modes, the position of transitory EMG may sometimes
not be located.
2.8.5
EMG detail information <2>
The type of the cas sette tape and the cassette tape winding po-
sition can be confirmed based on the figure in EMG detail infor-
mation<2>.
[FDP /OS D dis play]
*5 : *6 : *7
Note:
•
EMG detail information <2> is the reference informa-
tions tored using the remaining tape detection function
of the cassette tape. As a result, it may not identify cas-
sette correctly when a special cassette tape is used or
when the tape has variable thickness.
*5 : Cassette tape type <1>
Notes:
•
Cassette tape type <1> is identified a few times during
mode transition and the identification count is variable
depending on the cassette tape type. If an EMG occurs
in the middle of identification, the cassette tape type
may not be able to be identified.
•
If other value than those listed in the above table is dis-
played, the cassette tape type is not identified.
*6 : Cassette tape winding position
The cassette tape winding position at the moment of EMG is dis-
played by dividing the entire tape (from the beginning to the end)
in 22 sections using a hex number from “00” to “15”.
*7 : Cassette tape type <2> (Winding area)
Note:
•
The values of cassette tape type <2> in the above table
are typical values with representative cassette tapes.
2.8.6
EMG detail information <3>
Three deck operation modes preceding the deck operation mode
in which the EMG occurs may be confirmed based on the figures
in the EMG information detail <3>. For the contents of the dis-
played information, see the table "Deck operation mode" in sec-
tion "2.8.4 EMG detail information <1>".
* 5 : Type of the cas sette tape in use <1>
* 6 : Winding pos ition of the cas sette tape in use
* 7 : Type of the cas sette tape in use <2> (Winding area)
0-
VHS
Cassette insertion
Tab broken
ON
ON
1-
VHS
Cassette insertion
Tab broken
ON
OFF
2-
VHS
Cassette insertion
Tab broken
OFF
ON
3-
VHS
Cassette insertion
Tab broken
OFF
OFF
4-
VHS
Cassette insertion
Tab present
ON
ON
5-
VHS
Cassette insertion
Tab present
ON
OFF
6-
VHS
Cassette insertion
Tab present
OFF
ON
7-
VHS
Cassette insertion
Tab present
OFF
OFF
8-
S-VHS
Cassette ejection
Tab broken
ON
ON
9-
S-VHS
Cassette ejection
Tab broken
ON
OFF
A-
S-VHS
Cassette ejection
Tab broken
OFF
ON
B-
S-VHS
Cassette ejection
Tab broken
OFF
OFF
C-
S-VHS
Cassette ejection
Tab present
ON
ON
D-
S-VHS
Cassette ejection
Tab present
ON
OFF
E-
S-VHS
Cassette ejection
Tab present
OFF
ON
F-
S-VHS
Cassette ejection
Tab present
OFF
OFF
Mechanism sensor information
Display
MN* / HD*
M3*
REC safety
Start
End
S-VHS SW
CASS SW
SW
sensor
sensor
-0
-7
-
Initial value
-1
-0
-
EJECT position
-
-
-0
EJECT position (Cassette housing drive mode)
-2
-7
-
Housing operating
-
-
-1
Between EJECT and U / L STOP
-3
-1
-2
U / L STOP position
-
-
-3
Guide arm drive position
-4
-7
-4
Tape being loaded / unloaded (When the pole base is
located on the front side of the position just beside the
drum)
-5
-2
-5
Tape being loaded / unloaded (When the pole base is
located on the rear side of the position just beside the
drum)
-6
-7
-6
Pole base compressed position
-7
-3
-F
FF / REW position
-8
-7
-F
Between FF / REW and STOP with pinch roller compres-
sion ON
-9
-4
-F
STOP with pinch roller compression OFF
-A
-7
-E
Between STOP with pinch roller compression OFF and
REV
-B
-5
-
REV (REV STILL / SLOW) position
-
-
-D
REV position
-
-
-C
Between REV and REV STILL / SLOW
-
-
-B
REV STILL / SLOW position
-C
-7
-
Between REV and FWD
-
-
-A
Between REV STILL / SLOW and FWD STILL / SLOW
-D
-6
-
FWD (FWD STILL / SLOW) position
-
-
-9
FWD STILL / SLOW position
-E
-7
-
Between FWD and PLAY
-
-
-8
Between FWD STILL / SLOW and PLAY
-F
-6
-7
PLAY position
Display
Mechanism mode position
MN* HD* M3*
"00"
: End of winding
"15"
: Beginning of winding
"FF or - -" : Tape position not identified
Display
Cassette tape type <1>
00
Cassette type not identified
16
Large reel/small reel (T-0 to T-15/T-130 to T-210) not classified
82
Small reel, thick tape (T-120) identified/thin tape (T-140) identified
84
Large reel (T-0 to T-60) identified
92
Small reel, thick tape (T-130) identified/thin tape (T-160 to T-210) identified
93
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) not classified
C3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
D3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
E1
C cassette, thick tape (TC-10 to TC-20) identified
E2
Small reel, thick tape (T-0 to T-100) identified
E9
C cassette, thin tape (TC-30 to TC-40) identified
F1
C cassette, thick tape/thin tape (TC-10 to TC-40) not classified
Display
Cassette tape type <2>
00
Cassette type not identified
07
Small reel, thick tape
T-5
08 - 0E
C cassette, thick tape
TC-10
09 - 15
C cassette, thick tape
TC-20P
0A - 0B
Small reel, thick tape
T-20
0A - 16
C cassette, thin tape
TC-30
0A - 16
C cassette, thin tape
TC-40
0D - 0F
Small reel, thick tape
T-40
11 - 14
Small reel, thick tape
T-60
15 - 18
Small reel, thick tape
T-80 / DF-160
17 - 1A
Small reel, thick tape
T-90 / DF-180
19 - 1D
Small reel, thick tape
T-100
1D - 21
Small reel, thick tape
T-120 / DF-240
1E - 1F
Small reel, thin tape
T-140
1F - 23
Small reel, thick tape
T-130
21 - 23
Small reel, thin tape
T-160
21 - 23
Small reel, thin tape
T-168
22 - 24
Small reel, thick tape
DF-300
22 - 24
Small reel, thin tape
T-180 / DF-360
22 - 24
Small reel, thin tape
T-210 / DF-420
22 - 23
Large reel
T-5
23 - 24
Large reel
T-10
25 - 26
Large reel
T-20
27 - 29
Large reel
T-30
29 - 2B
Large reel
T-40
2D - 2F
Large reel
T-60
