background image

Other Functions

Checking tape position

When you change the recorder operation
mode from the stop mode to fast forward
or rewind mode, or when you perform an
Index Search or Instant Review, the tape
position indicator appears.
The position of “

q

” in relation to “ 0”

(beginning) or “+” (end) shows you where
you are on the tape.

Set “O.S.D.” to “ON”.

Changing display information

Each time you press

– –:– –

, the display panel shows

the channel number and the clock time alternatively.

You can change display in the stop, recording or
recording pause mode, or during rewind/fast-
forward high-speed search.

When “O.S.D.” is set to “ON” and

– –:– –

on the

remote control is pressed, time counter will appear on the TV
screen. To reset the time counter, press

0000

on the remote

control.

Function settings

You can use the other useful function settings on the Function Set
screen.

Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.

A

Access Main Menu screen, then
Function Set screen

Press

MENU

on the remote control. Press

rt

to place the pointer next to

“FUNCTION SET”, then press

OK

or

e

.

B

Select Function

Press

rt

to place the pointer next to the

function you want to set.

C

Change setting

Press

OK

or

e

. The default setting is

bold

in the following table.

Press

MENU

to return to normal screen.

B.E.S.T.

ON

/ OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is
set to “ON”, this recorder checks the condition of the tape in use
during playback and recording, and compensates to provide the
highest-possible pictures. This takes place whenever you play
back a tape or start recording after inserting a tape.

NOTE:

The recorder checks the tape condition for about 7 seconds, then
starts recording. To make sure you record the desired scene or
program completely, perform the following steps:

A

Press and hold

PAUSE

(

9

), and press

REC

(

7

). After about

7 seconds, the recorder re-enters Record Pause mode.

B

Press

PLAY

(

4

) to start recording.

PICTURE CONTROL

AUTO

(NORM) / EDIT / SOFT / SHARP

This function helps you to adjust the playback picture quality
according to your preference.

AUTO

(NORM)

: Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear
instead of “AUTO”.

EDIT

: Minimizes picture degradation during editing (recording and

playback).

SOFT

: Reduces image coarseness when viewing overplayed tapes

containing much noise.

SHARP

: Clearer, sharper-edged picture when viewing images with

much flat, same-coloured surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing
the tapes, select “AUTO”.

PAL/MESECAM

AUTO

/ PAL / MESECAM

Select the appropriate colour system for recording or playback.

AUTO

: Usually set to this mode. The appropriate colour system

(PAL or MESECAM) will be selected depending on the playback or
recording signals.

If the “AUTO” mode does not work properly, select either of the
following manual modes.

PAL

: To record PAL signals, or playback a PAL tape.

MESECAM

: To record SECAM signals, or playback a SECAM or

MESECAM tape.

NOTES:

SECAM signals will always be recorded as MESECAM. Select
“AUTO” or “MESECAM” when recording SECAM signals.

When playing back a SECAM tape, select “AUTO” or
“MESECAM”. The playback picture will always be
monochrome.

NTSC

NTSC3.58

/ NTSC4.43 / NTSC

]

PAL

To record NTSC signals or playback a NTSC tape, it will be
necessary to select the appropriate mode.

NTSC3.58

: To record NTSC signals or playback a NTSC tape.

NTSC4.43

: To record NTSC4.43 signals or playback a NTSC4.43

tape.

NTSC

]

PAL

: To playback a NTSC tape on PAL TV.

NOTE:

The “NTSC

]

PAL” mode does not work during recording. In this

mode, NTSC signals will be recorded as NTSC3.58.

The Menu screen is distorted during playing back a NTSC tape
on PAL TV. Stop playback and access the Menu screen again.

In the “NTSC4.43” mode, with some TVs, on-screen displays
(Program screen, etc.) may roll up or down and there may be a
loss of colour. When this happens, select the “NTSC3.58”
mode.

AUTO TIMER

— ON /

OFF

When this function is set to “ON”:

The timer recording standby mode is automatically engaged when
the recorder is turned off. It is temporarily canceled when the
recorder is turned on.You do not have to press

#

to engage or

disengage the timer recording standby mode.

When this function is set to “OFF”:

You have to press

#

to engage or disengage the timer recording

standby mode.

O.S.D.

ON

/ OFF

When this function is set to “ON”, various recorder status
information (on-screen display) appears on the screen.

NOTE:

When you use this recorder as the source player for editing a tape,
be sure to set this function to “OFF”; otherwise, the recorder status
information (on-screen display) will be recorded on the edited
tape.

0

+

+

+

+

5

[

/

]

[MENU] : EXIT

MAIN MENU

FUNCTION SET

TUNER SET
INITIAL SET

[

/

]

[MENU] : EXIT

FUNCTION

B.E.S.T.

ON

PICTURE CONTROL

AUTO

PAL/MESECAM

AUTO

NTSC

NTSC3.58

AUTO TIMER

OFF

O.S.D.

ON

AUTO SP LP TIMER

OFF

Summary of Contents for HR-J285EA

















Reviews: