37
Refer to the illustrations on page 36.
LOCATE EDIT-IN POINT
7
Find the point on the source
tape from where you want
the edited scene to begin by
pressing PUSH JOG
™£
, then press OK.
●
The edit-in point is
registered in memory and
appears on the screen.
●
You can also perform an
Index Search (if index marks have been previously
recorded on the tape at the desired points –
Z
pg. 18)
to find the points you want, but this will result in
reduced accuracy.
LOCATE EDIT-OUT POINT
8
Find the point where you
want the edited scene to
end by pressing PUSH JOG
™£
, then press OK.
●
The edit-out point is
registered in memory and
appears on the screen.
●
The total time of the
edited scenes is displayed
to the right of "TTL".
●
Repeat steps 7 and 8 for
each additional scene.
PREPARE RE-
CORDING
DECK
9
Engage its Record-Standby mode.
START R.A. EDIT
10
Press C.MEMORY.
●
Automatic editing begins; all the specified scenes are
copied to the recording deck in the order they were
registered.
●
The on-screen display remains while your VCR
searches for each scene (blinking cursor indicates
scene currently being searched for), but disappears
during actual editing.
●
During scene search, the recording deck automati-
cally enters its Record-Standby mode. "SEARCHING"
appears on the screen.
●
When all registered scenes have been edited, your
VCR enters the PAUSE mode, the recording deck
enters its Record-Standby mode, and the cursor blinks
at the next available number.
R.A. EDIT
EDIT MODE
=
1
0:00:00
2
3
4
5
6
7
8
TTL 0:00:00
CNT 0:00:00
END R.A. EDIT
11
Press MENU as many times as necessary to return to the
normal screen, and engage the Stop mode for the
recording deck.
NOTES:
●
You can also monitor the sound when searching for scenes
you want to edit in steps 7 – 8. Since you can hear the
soundtrack during selection, you can avoid abrupt or
unnatural sounding scene-to-scene transitions.
●
When editing, there may be a discrepancy of about 2 seconds
on the source tape between the locations you chose as edit-in/-
out points and the locations the VCR recognizes as those points.
●
For any scene, the edit-out point must have a counter reading
that is at least 1 second after the corresponding edit-in point. Any
less than 1 second and the edit-out point will not be registered.
●
Since the source VCR prerolls during Random Assemble
Editing, there must be at least 15 seconds worth of recorded
material prior to any edit-in point on the source tape.
●
If the search time for an edit-in point exceeds 5 minutes, the
recording deck enters its Stop mode and editing will not take
place.
To Make Corrections . . .
. . . during step 7 or 8, you can cancel registered in and out
points by pressing CANCEL on the remote control. Each time
you press, the preceding point is erased.
●
If, for example, you have registered 5 sets of in and out points
and want to reset the first set, you have to press CANCEL until
all points after the first set have been erased. Reenter them
after you've repaired the first set of points.
Memory Capacity
Random Assemble Editing shares
memory space with the VCR's
timer. If there are programs
occupied by timer-recording data,
those spaces cannot be used to
register edit-in and -out points —
meaning you won't be able to edit
8 scenes.
●
When all 8 programs are full, "PROGRAM FULL" appears on
the R.A. EDIT screen.
●
To cancel a program, see page 30.
RM-V403U Multi-Brand R.A. Edit Controller
(Not supplied)
By connecting this controller to your VCR's R.A. EDIT connec-
tor, you can perform Random Assemble Editing in combination
with a second non-JVC VCR. The controller is compatible with
various major VCR brands. For compatible systems and
availability, please consult your JVC dealer.
R.A. EDIT
EDIT MODE
PROGRAM FULL
TTL 0:00:00
CNT 0:00:00
R.A. EDIT
EDIT MODE
=
1
0:02:23
2
3
4
5
6
7
8
TTL 0:00:00
CNT 0:02:23
R.A. EDIT
EDIT MODE
1
0:02:23
0:02:51
=
2
3
4
5
6
7
8
TTL 0:00:28
CNT 0:02:51
