13
2
1
Use:
for Hi-Fi stereo tapes
for main audio of bilingual tapes
for sub audio of bilingual tapes
for audio-dubbed tapes
for audio-dubbed tapes
Track (on display panel):
L + R
L
R
NORM
L + R+NORM
=
=
=
=
=
Counter memory
During Playback:
Press C.RESET button at a point you wish to locate
later.
L
L
L
L
L
The counter will read “0:00:00”.
Press C.MEMORY button.
L
The
M
indicator will light on the display panel.
When you wish to return to that point, press Stop
7
button and then Rewind
1
button.
L
The tape will rewind and stop at about “0:00:00” automatically.
To cancel the Counter Memory mode, press C. MEMORY
button again.
Next function memory
Your recorder can memorise what to do after rewind.
During Stop:
L
For automatic power off after the tape is rewound
1 Press Rewind
1
1
1
1
1
button.
2 Press OPERATE button within 2 seconds.
Repeat playback
During Playback:
Press Play
-
button for more than 5 seconds, and release.
L
The PLAY indicator on the display panel will blink slowly.
L
The tape will be played all the way to the end, 20 times
automatically, and then stop.
To stop playback at any time, press Stop
7
button.
Soundtrack selection
During Playback:
Your video recorder is capable of recording three soundtracks
(HIFI L, HIFI R and NORM) simultaneously, and playing back
the selected soundtrack.
L
Pressing AUDIO MONITOR changes the track:
Note:
•
Normally use the “L + R” position. Then Hi-Fi stereo tapes are
played back in stereo, and tapes with normal audio only are
played back automatically in the NORM mode.
Wide quality
Use this function to improve image contrast which tends to
degrade especially with wide-screen TVs.
During Playback:
Press WIDE QUALITY button on the recorder.
L
L
L
L
L
The button will light in “green”.
L
L
L
L
L
Pressing the button again turns off the light.
L
L
L
L
L
Turn on/off the light according to the type of playback
picture you want.
L
L
L
L
L
The setting will remain effective even though you turn on/off
the recorder.
L
L
L
L
L
This function is also effective with large-screen 4:3 aspect
ratio TVs as well.
Index search
Your recorder automatically marks index codes at the beginning
of each recording. This function gives you quick access to any
one of 99 index codes in either direction.
During Stop:
Press SEARCH SYSTEM to make the BLANK indicator
disappear on the front panel.
Press
g
or
f
button.
L
g
1 or
f
1 will be displayed on the screen and search
will begin in the corresponding direction.
If you wish to access index codes 2 through 99, press
g
or
f
button repeatedly until the correct index
number is displayed.
Example:
To locate the beginning of B from the current position,
press
g
button twice.
To locate the beginning of D from the current position,
press
f
button once.
L
When the specified index code is found, playback will start
automatically.
To mark an index code manually
During Playback or Still:
Press INDEX MARK button on the remote control.
L
The recorder will mark an index code at that location.
To erase an index code
During Playback or Still:
Press INDEX ERASE button on the remote control.
L
The recorder will fast-forward to the nearest index code and
erase it. Playback continues after the index code is erased.
Note:
•
If the tape’s safety tab has been removed, index codes
cannot be marked or erased.
Playback (cont’d)
1
1
1
1
1
2
3
Current Position
Index number
2
4
3
