background image

— 9 —

Page 9

November 8, 2002 9:15 am

Basic Playback

A

Load a cassette

Make sure the window side is up, the rear label side is facing you 
and the arrow on the front of the cassette is pointing towards the 
VCR.

Do not apply too much pressure when inserting.

The VCR turns on, and the counter on the on-screen display is 
reset, automatically.

If the cassette’s record safety tab has been removed, playback 
begins automatically.

B

Start playback

Press 

PLAY

 (

4

).

The S-VHS indicator lights up when you play back a tape 
recorded in S-VHS mode or in S-VHS ET mode (

pg. 11).   

Playback Features

Adjusting tracking condition
— Tracking Adjustment

Automatic tracking adjustment

Whenever you insert a tape and start playback, automatic tracking 
starts working and continuously analyzes the signal to enable 
optimum picture quality during playback.

Manual tracking adjustment

If automatic tracking cannot eliminate noises well during 
playback, follow the procedures below.

On the Remote

A

Press 

SP/EP

 during playback to activate manual tracking.

B

Press 

CH

r

/

t

 to eliminate the noises. Press it briefly for a fine 

adjustment, or press and hold for a coarse adjustment.

Press 

SP/EP

 again to reactivate automatic tracking.

Selecting monitor sound
— Audio Monitor

While playing back a tape on which stereo sound or SAP sound is 
recorded, press 

A.MONITOR

 on the Remote. Each time you press 

the button, sound changes.

HI-FI

: Normally select this. Hi-Fi sound is played back.

HI-FI L

: Sound on the left Hi-Fi channel is played back.

HI-FI R

: Sound on the right Hi-Fi channel is played back.

NORM

: Sound on the normal track is played back.

NORM HI-FI

: Both sounds on the Hi-Fi track and normal track are 

mixed and played back. 

NOTE:

The above indication appears when “SUPERIMPOSE” is set to 
“ON” 

(

pg. 13), though the monitor sound changes in 

sequence.

Automatic operations after rewinding
— Next Function Memory

The Next Function Memory “tells” the VCR what to do after 
rewinding is complete. Ensure that the VCR is in stop mode.

For Automatic Playback Start

Press 

REW

 (

3

), then press 

PLAY

 (

4

) within 2 seconds.

For Automatic Power Off

Press 

REW

 (

3

), then press 

POWER 

1

 within 2 seconds.

Playback

Turn on the VCR and TV, and select the VCR channel (or AV 

mode).

During playback

Stop playback

Press 

STOP

 (

8

) on the 

Remote.

OR

Press 

STOP/EJECT

 (

0

) on 

the VCR.

Pause playback and view still picture

Press 

PAUSE

 (

9

).

Press 

PLAY

 (

4

) to resume normal playback.

NOTE:

During still picture, vertical vibration may appear on the TV  
screen. Press 

CH

r

/

t

 on the Remote to get a clearer picture.

Pause and Frame-by-Frame playback

Press 

PAUSE

 (

9

) to pause, then press 

2

or 

6

(or 

PAUSE

 (

9

)) 

repeatedly.

Press 

PLAY

 (

4

) to resume normal playback.

Picture Search

Press 

REW

 (

3

) or 

FF

 (

5

). Press 

REW

 (

3

) or 

FF

 (

5

again to perform high-speed search.

Each time you press 

REW

 (

3

) or 

FF

 (

5

), the search speed 

changes between low-speed and high-speed.

Press 

PLAY

 (

4

) to resume normal playback.

Variable-Speed Picture Search (including slow-motion)

Press 

2

or 

6

 repeatedly.

Press 

PLAY

 (

4

) to resume normal playback.

Each time you press 

2

or 

6

, the playback speed 

changes. To decrease the speed during picture search, press the 
opposite direction button repeatedly.

During still picture, press and hold 

6

 

to start forward (or 

2

 

to start reverse) slow motion playback. When you release 

the button, still picture resumes. During still picture, holding 

PAUSE

 (

9

) for more than 2 seconds also starts forward slow 

motion playback. If you press 

PAUSE

 (

9

) again, still picture 

resumes.

NOTE:

During slow motion, some noise may appear on the TV screen. 
Press 

CH

r

/

t

 on the Remote to eliminate the noise.

S-VIDEO 

When the tape is not running

Rewind/fast-forward

Press 

REW

 (

3

) or 

FF

 (

5

).

Eject the cassette

Press 

STOP/EJECT

 (

0

).

You can also eject the cassette when the VCR is turned off.

Turn off the VCR

Press 

POWER 

1

.

Turn on the VCR and TV, and select the VCR channel (or AV 

mode).

Reverse

Forward

Reverse 

search 

3 steps

Reverse 

play

Reverse 

slow 

motion 

1 step

Slow 

motion 

1 step

Normal 

play

Forward 

search 

4 steps

CONTINUED ON NEXT PAGE

HR-S2912U-EN.fm Page 9 Friday, November 8, 2002 9:15 AM

Summary of Contents for HR-S2912U

















Reviews: