February 8, 2003 4:06 pm
Page 5
— 5 —
Master Page: Right
With AV connection
Press
PR –
until the display panel shows
“1 – –” (or “2 – –”). Now the video channel
is set to off. Then press
OK
.
●
To view picture signals from the recorder, set your TV to its AV
mode.
E
Check results
If both Auto Channel Set and Clock Set
have been performed successfully, the
correct current time is displayed.
Turn on the TV and select its video channel
or AV mode. Then make sure that all necessary stations have been
stored in the recorder’s memory by using the
PR
button(s).
If Auto Channel Set has succeeded but
Clock Set has not, “1” is displayed.
A
Turn on the TV and select its video
channel or AV mode. Then make sure that all
necessary stations have been stored in the recorder’s memory by
using the
PR
button(s).
B
Perform “Clock Set” (
墌
13).
If both Auto Channel Set and Clock Set
have failed, “– –:– –” is displayed.
Make sure the cables are connected properly.
Turn off the recorder once, then turn the
recorder back on again. The Country Set screen appears on the
screen. Perform “Auto Set Up” again.
Language Set
You can change the language setting manually as required.
A
Access Main Menu screen, then Auto
Channel Set screen
Press
MENU
. Press
rt
to place the
pointer next to “AUTO CH SET”, then press
OK
or
e
.
B
Select your country
Press
rt
to place the pointer next to your
country, then press
OK
or
e
.
C
Select language
Press
rt
to place the pointer next to the desired language.
●
You do not have to press
OK
; pressing
OK
starts Auto Channel
Set.
D
Return to normal screen
Press
MENU
.
Basic Playback
A
Load a cassette
Make sure the window side is
up, the rear label side is facing
you and the arrow on the front of
the cassette is pointing towards
the recorder.
●
Do not apply too much pressure when inserting.
●
The recorder turns on, and the counter is reset, automatically.
●
If the cassette’s record safety tab has been removed, playback
begins automatically.
B
Start playback
Press
4
.
The S-VHS indicator lights up when you play back a tape recorded
in S-VHS mode or in S-VHS ET mode (
墌
8).
OUTPUT/INPUT SET
CLOCK SET
Playback
Turn on the TV and select the video channel or AV mode.
During playback
Stop playback
Press
8
on the remote
control.
OR
Press
0
on the recorder.
Pause playback and view still picture
Press
9
.
●
Press
4
to resume normal playback.
●
If there is vertical jitter, press
PR
r
/
t
on the remote control or
PR+/–
on the recorder to correct the picture.
Pause and Frame-by-Frame playback
Press
9
to pause, then press
w
or
e
(or
9
) repeatedly.
●
Press
4
to resume normal playback.
Picture Search
Press
3
or
5
. Press
3
or
5
again to perform high-
speed search.
●
Each time you press
3
or
5
, the search speed changes
between low-speed and high-speed.
●
Press
4
to resume normal playback.
Variable Speed Search (including slow-motion)
Press
w
or
e
repeatedly.
●
Press
4
to resume normal playback.
●
Each time you press
w
or
e
, the playback speed changes. To
decrease the speed during picture search, press the opposite
direction button repeatedly.
●
During still picture, press and hold
e
to start forward (or
w
to
start reverse) slow motion playback. When you release the
button, still picture resumes. During still picture, holding
9
for
more than 2 seconds also starts forward slow motion playback.
If you press
9
again, still picture resumes.
●
During slow motion playback, some noise may appear on the
TV screen. Press
PR
r
/
t
on the remote control or
PR+/–
on
the recorder to eliminate the noise.
Reverse
search
3 steps
Reverse
play
Reverse
slow
motion
1 step
Slow
motion
1 step
Normal
play
Forward
search
4 steps
Reverse
Forward
HR-S5960.5961_001EN.fm Page 5 Saturday, February 8, 2003 4:07 PM
