Page 10
April 17, 2001 9:00 am
— 10 —
Timer Recording
Up to 8 timer recording programs can be made using Express
timer programing method as far as a year in advance. Remember,
the clock must be set before you can program the timer.
NOTES:
●
If all the 8 programs have already been set, “PROGRAM FULL”
appears on the TV screen.
●
After timer recording is completed, the VCR turns off
automatically.
●
You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
●
To timer-record cable channels, be sure to keep the cable box
turned on with the correct channel selected.
●
In case of a power failure after programming, the VCR’s memory
backup keeps your selections (if the lithium battery is not
exhausted).
●
If the tape reaches its end during timer recording, the recording
stops and “
#
“, “
䡬
” and “
$
” on the display panel blink. Press
#
to disengage timer, then press
STOP/EJECT
(
0
) on the
VCR to eject the cassette or press
POWER
1
then press
REW
(
3
) to rewind the tape.
Express Timer Programing
Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.
A
Press
PROG
on the Remote to access the Program screen.
B
Press
START+/–
,
STOP+/–
,
DATE+/–
or
PR+/–
repeatedly to enter the start
time, stop time, date or channel.
●
Press and hold
START+/–
or
STOP+/–
to increase the time in
30-minute intervals.
●
To set the tape speed, press
SP/EP
(
p
).
●
To timer-record daily (Monday–Friday) or weekly serials,
press
DAILY
(
M-F
) (
Number key “8”
) or
WEEKLY
(
Number
key “9”
). Pressing the button again makes the “DAILY” or
“WEEKLY” display disappear.
C
Press
OK
or
PROG
.
●
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, see “Program overlap warning display” (
墌
pg. 11).
D
Press
#
. The VCR turns off automatically and “
#
” is displayed
on the display panel.
To use the VCR while it is in timer
recording standby mode
Press
#
, then press
1
. After you use the VCR, press
#
again to
put the VCR into timer recording standby mode.
Checking, canceling or changing
program settings
A
Disengage timer
Press
#
, then press
1
.
●
When “AUTO TIMER” (
墌
pg. 12) is set to “ON”, you do not
have to press
#
.
B
Access Program Check screen
Press
"
(
CHECK
).
C
Access Program screen
Press
"
(
CHECK
) again. Each time you
press
"
(
CHECK
), the next program’s
Program screen appears.
D
Cancel or change program setting
To cancel a program,
press
&
(
CANCEL
) when the Program
screen you do not want is shown.
To change a program,
press the appropriate button:
START+/–
,
STOP+/–
,
DATE+/–
,
PR+/–
,
DAILY
(
M-F
) (
Number key “8”
),
WEEKLY
(
Number key “9”
) and/or
SP/EP
(
p
) when the Program
screen on which you want to make changes is shown.
E
Return to normal screen
Press
"
(
CHECK
) repeatedly until no Program screen is shown.
F
Reengage timer recording standby mode
Press
#
. The VCR turns off automatically and “
#
” is displayed on
the display panel.
●
When “AUTO TIMER” (
墌
pg. 12) is set to “ON”, the timer
recording standby mode automatically resumes when you turn
off the VCR.
PROGRAM 1
START
STOP
– –:– –AM
– –:– –AM
DATE
CH
– –/– –/– –
– – – SP
PRESS (+/
–
, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
PRESS (CHECK) TO NEXT
PR START
STOP
CH
DATE
1
8:00P
10:00
12
12/24
2
10:00A
10:45 40
12/25
3
11:30P
1:00 125
12/25
4
5
6
7
8
PROGRAM 1
START
STOP
8:00 PM
10:00 PM
DATE
CH
12/24/02
12
SP
PRESS (CANCEL) TO CANCEL
PRESS (CHECK) TO NEXT
– Timer Recording –
+5-80(1IP3DJH7XHVGD\$SULO$0
