JVC HR-S9700EK Service Manual Download

Page: 35 / 87

3-1

SECTION 3

ELECTRICAL ADJUSTMENT

3.1 PRECAUTION

The following adjustment procedures are not only necessary
after replacement of consumable mechanical parts or board
assemblies, but are also provided as references to be re-
ferred to when servicing the electrical circuitry.
In case of trouble with the electrical circuitry, always begin a
service by identifying the defective points by using the meas-
uring instruments as described in the following electrical ad-
justment procedures. After this, proceed to the repair, replace-
ment and/or adjustment. If the required measuring instruments
are not available in the field, do not change the adjustment
parts (variable resistor, etc.) carelessly.

3.1.1 Required test equipments

• Color (colour) television or monitor
• Oscilloscope:

wide-band, dual-trace, triggered delayed
sweep

• Frequency counter
• Signal generator: RF / IF sweep / marker
• Signal generator: stairstep, color (colour) bar [PAL]
• Recording tape
• Digit-key remote controller(provided)

3.1.2

Required adjustment tools

3.1.3 Color (colour) bar signal,Color (colour) bar pattern

Fig. 3-1-4a Jig RCU [PTU94023B]

3.1.4

Switch settings and standard precautions

The SW settings of the VCR and the standard precautions
for the electrical adjustments are as follows.

• When using the Jig RCU, set its custom code to match

the custom code of the VCR.

• Set the switches as shown below unless otherwise

specified on the relevant adjustment chart. The
switches that are not listed below can be set as de-
sired.
If the VCR is not equipped with the functions detailed
below, setup is not required.

AUTO PICTURE/VIDEO CALIBRATION/

OFF

B.E.S.T./D.S.P.C.

PICTURE CONTROL/SMART PICTURE

NORMAL/NATURAL

VIDEO STABILIZER

OFF

TBC

Digital 3R

VIDEO NAVIGATION/TAPE MANAGER

OFF

• Unless otherwise specified, all measuring points and

adjustment parts are located on the Main board.

• In the Signal column of the adjustment chart, “Ext. S-

input” means the Y/C separated video signal and “Ext.
input” means the composite video signal input.

Jig RCU

PTU94023B

Alignment tape

(SP, stairstep, PAL)

MHPE

Alignment tape

(LP, stairstep, PAL)

MHPE-L

LPF

PTU93006

Alignment tape

(SP stairstep, NTSC)

MHP

Alignment tape

(S-VHS, SP/LP, color (colour) bar)

MH-2H

INITIAL MODE

DATA CODE

CUSTOM CODE
43: A

CODE

53: B

CODE

[Data transmitting method]
Depress the “ ” ( 3 ) button
after the data code is set.

Jig RCU

3.1.5 EVR Adjustment

Some of the electrical adjustments require the adjustment
performed by the EVR system. The Main board assembly
have EEPROMs for storing the EVR adjustment data and
user setups.

Notes:
• In the EVR adjustment mode, the value is varied with

the channel buttons (+, –). The adjusted data is stored
when the setting mode changes (from PB to STOP,
when the tape speed is changed, etc.). Take care to
identify the current mode of each adjustment item
when making an adjustment.

• When changing the address setting in the EVR adjust-

ment mode, use the Jig RCU or the remote controller
having numeric keypad with which a numeric code can
be directly input.
The remote control code of the Jig RCU corresponds
to each of the digit keys on the remote controller as
follows.

• As the counter indication and remaining tape indica-

tion are not displayed FDP during the EVR adjustment
mode, check them on the TV monitor screen.

• When performing the EVR adjustment, confirm that the

FDP indication is changed to the EVR mode, as shown
below.

Digit-key

Code

20 21

22 23

27 28 29

(75%)

White(75%)

0.7 V