JVC HR-V610AH, Instructions Manual

Page 8

June 9, 2004 1:32 pm

— 8 —

Timer Recording

Up to 8 timer recording programs can be made using G-

CODE

timer programing or Express timer programing method as far as a 
year in advance. Remember, the clock must be set before you can 
program the timer.

NOTES:

●

If all the 8 programs have already been set, “PROGRAM FULL” 
appears on the TV screen.

●

After timer recording is completed, the recorder turns off 
automatically.

●

You can program the timer recording while a regular recording 
is in progress; the menu screens will not be recorded.

●

In case of a power failure after programming, the recorder’s 
memory backup keeps your selections (if the lithium battery is 
not exhausted).

●

If the tape reaches its end during recording, the recording stops 
and “ 

” and “ 

$

” on the front display panel blink. Press 

1

then

0

  on the recorder to eject the cassette or press 

3

on the remote control to rewind the tape.

G-

CODE

®

 System Setup

INFORMATION

The G-

CODE

 timer programming system eliminates the need to 

input channel, date, start and stop time data when setting the 
timer record function. Simply key in the G-

CODE

 number for the 

TV programme you wish to record (found in most TV listings) and 
the recorder's timer is automatically programmed.
You have to set “GUIDE PROG” numbers, which are assigned to 
each station for purposes of G-

CODE

 timer programming, for all 

the stations stored in your recorder’s memory to get proper results.
Before G-

CODE

 setup you must have performed the procedures of 

Tuner Set and Clock Set.

IMPORTANT

Perform the following procedure after Auto Set Up and/or the 
channel setting steps.
After setting the Guide Program Numbers, channel positions may 
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting. 

Guide Program Number Set

A

Access Main Menu screen, then Initial Set screen

Press 

MENU

 on the remote control. Press 

rt

 to place the 

pointer next to “INITIAL SET”, then press 

OK

 or 

e

.

B

Access G-

CODE

 Setup screen

Press 

rt

 to place the pointer next to “G-CODE/SHOWVIEW 

SETUP”, then press 

OK

 or 

e

.

C

Input Guide Prog number

Press 

rt

 or the 

Number keys

 to select 

the Guide Program number as shown in 
the TV listing, then press 

OK

 or 

e

.

D

Input receiving channel number

Press 

rt

 or the 

Number keys

 to select 

the number of the channel on which the 
Guide Program number’s broadcasts are 
received, then press 

OK

 or 

e

.

●

If the satellite broadcast is received on 
your recorder's auxiliary channel (“L-1” 
or “F-1”), select “L-1” or “F-1” for the channel position to which 
the satellite receiver is connected.

●

Repeat steps 

3

 and 

4

 as necessary.

E

Return to normal screen

Press 

MENU

 on the remote control.

G-

CODE

®

 Timer Programing

The G-

CODE

 numbers are the numbers 

next to the program in most TV listing.

●

Remember, the clock must be set 
before you can program the timer.

●

Be sure to read “G-

CODE

®

 System 

Setup”.

●

Load a cassette with the record safety 
tab intact. The recorder turns on, and 
the counter is reset, automatically.

●

Select the appropriate colour system 
with “PAL/MESECAM” and “NTSC” 
in Function settings.

A

Press 

PROG

 on the remote control 

to access the G-

CODE

 screen.

B

Press the appropriate 

Number keys

 to input the G-

CODE

number, then press 

OK

. Check to make sure the setting is 

accurate on the G-

CODE

 Program screen.

●

If the G-

CODE

/S

HOW

V

IEW

 Setup 

screen appears after pressing 

OK

, 

press the 

Number keys

, 

PR+/–

 or 

rt

 to input the number of the 

channel on which the broadcast for 
the G-

CODE

 number is received on 

the recorder, then press 

OK

.

●

To set the tape speed, press 

SP/LP/EP 

(

p

).

●

To change the stop time, press 

STOP+/–

.

●

To timer-record daily (Monday–Friday) or weekly serials, 
press 

DAILY 

(number key 8) or 

WEEKLY 

(number key 9). 

Pressing the button again makes the “DAILY” or “WEEKLY” 
display disappear.

●

If you made a mistake, press 

&

 to access the G-

CODE

 screen 

again.

●

If an incorrect G-

CODE

 number or the one for a broadcast 

already finished has been input, “ERROR” is displayed for 
about 5 seconds, then the G-

CODE

 screen reappears.

C

Press 

OK

 or 

PROG

.

●

If “PROGRAM OVERLAPPED” appears, see “Program 
overlap warning display” (

9).

D

Press 

#

. The recorder turns off automatically and “

#

” is 

displayed on the display panel.

The SHOWVIEW system is not applicable with this model.

G-CODE/SHOWVIEW SETUP

   GUIDE PROG

      TV PROG

             2     

           5

 [

0–9] OR [    /    ] : SELECT 

 [MENU] : EXIT

G-CODE/SHOWVIEW SETUP

   GUIDE PROG

      TV PROG

             2     

           5

 [

0–9] OR [    /    ] : SELECT 

 [MENU] : EXIT

G-CODE/SHOWVIEW NO.

[0 – 9] 
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT

[0 – 9] 
[    ] : DELETE
[PROG] : EXIT

G-CODE/SHOWVIEW NO.

1 2 3 4 5 6 7 8       

: [OK]  

– P1 –

NO. 12345678

START

STOP

21:00

22:00

   SP

DATE

TV PROG

25.04

1

G-CODE/SHOWVIEW SETUP

   GUIDE PROG

      TV PROG

2

5

 [0–9] OR [    /    ] : SELECT 
 [PROG] : EXIT

HR-V610AH_EN.fm  Page 8  Wednesday, June 9, 2004  1:33 PM