background image

KS-DR3001D

B5E-0089-10/01 [W]

POWER AMPLIFIER

: INSTRUCTION MANUAL

 

English

 WARNING

• 

If the fuse blows, first make sure the wires aren’t touching to cause 

a short circuit then replace the old fuse with one with the same 

rating.

• 

Do not let pebbles, sand or metallic objects get inside the unit.

• 

Do not touch the unit during use because the surface of the unit 

becomes hot and may cause burns if touched.

 CAUTION

This unit is designed to operate on 12 V DC, NEGATIVE ground 

electrical systems. JVC recommends consulting a qualified technician 

for installation.

• 

To prevent short circuits while making connections, keep the 

battery’s negative terminal disconnected.

• 

This unit uses BTL (Balanced Transformerless) amplifier circuitry, 

i.e., floating ground system, so comply with the following:

Do not connect the “

·

” terminals of the speakers to each other.

Do not connect the “

·

” terminals of the speakers to the metal 

body or chassis.

• 

Cover the unused leads with insulating tape to prevent them from 

short circuiting.

• 

DO NOT disassemble the unit since there are no user serviceable 

parts inside.

• 

To keep the heat dissipation mechanism running effectively, wipe 

the accumulated dust off periodically.

• 

Listening to the tape, radio, CD or digital audio player, etc. with 

the volume set at a high level for a long period of time will exhaust 

the battery, while the engine is turned off or while the engine is 

idling.

• 

Use the speakers which have sufficient capacity to the unit.

B5E-0089_DR3001D.indd   1

2015/12/03   10:20

Summary of Contents for KS-DR3001D









Reviews: