2-13
Fig. 2-5-1d
Improper
Proper
( a ) Guide roller
( b ) Guide pole
Fig. 2-5-1c
A
B
C
D
Level drop at the guide roller (supply side)
Level drop at the guide roller (take-up side)
• Proper waveform variation: Always flat
• Improper waveform variation:
Higher
Lower
2.5.2
Height and tilt of the A/C head
Note:
• Set a temporary level of the height of the A/C head in
advance to make the adjustment easier after the A/C
head has been replaced. (See Fig.2-2-4c.)
(2)
(3)
(1)
Audio out
CTL.P
Guide pole (T.U)
bottom
flange
Guide pole (T.U)
Fig. 2-5-2a
(1) Play back the alignment tape (A).
(2) Apply the external trigger signal to D.FF (E), to observe
the AUDIO OUT waveform and Control pulse waveform
at the measuring points (D1) and (D2) in the ALT mode.
(3) Set the VCR to the manual tracking mode.
[KV-V8E]
Signal
(A)
•
Alignment tape(SP, stairstep, PAL) [MHPE]
[KV-V8J]
(A)
•
Alignment tape(SP, stairstep, NTSC) [MHP]
Mode
(B)
•
PB
Equipment
(C)
•
Oscilloscope
Measuring point
(D1)
•
AUDIO OUT terminal
(D2)
•
TP4001 (CTL. P)
External trigger
(E)
•
TP111 (D.FF)
Adjustment part
(F)
•
A/C head [Mechanism assembly]
Specified value
(G)
•
Maximum waveform
2.5.3
A/C head phase (X-value)
[KV-V8E]
Signal
(A)
•
Alignment tape(SP, stairstep, PAL) [MHPE]
[KV-V8J]
(A)
•
Alignment tape(SP, stairstep, NTSC) [MHP]
Mode
(B)
•
PB
Equipment
(C)
•
Oscilloscope
Measuring point
(D)
•
TP106 (PB FM)
External trigger
(E)
•
TP111 (D.FF)
Adjustment part
(F)
•
A/C head base [Mechanism assembly]
Specified value
(G)
•
Maximum V.PB FM waveform
Adjustment tool
(H)
•
A/C head positioning tool [PTU94010]
(1) Play back the alignment tape (A1).
(2) Apply the external trigger signal to D.FF (E), to observe
the V.PB FM waveform at the measuring point (D).
(3) Set the VCR to the manual tracking mode.
(4) Loosen the screws (4) and (5), then set the A/C head
positioning tool to the projected part in front of the A/C
head. (See Fig. 2-5-3a.)
(5) Turn the A/C head positioning tool fully toward the cap-
stan. Then turn it back gradually toward the drum and
stop on the first peak point position of the V.PB FM wave-
form output level. Then tighten the screws (4) and (5).
(6) Perform the tracking operation and make sure that the
V.PB FM waveform is at its maximum.
If it is not at maximum, loosen the screws (4) and (5),
and turn the A/C head positioning tool to bring the A/C
head to a position, around where the waveform reaches
its maximum for the first time. Then tighten the screws
(4) and (5).
(4) Adjust the AUDIO OUT waveform and Control pulse
waveform by turning the screws (1), (2) and (3) little by
little until both waveforms reach maximum. The screw (1)
and (3) are for adjustment of tilt and the screw (2) for azi-
muth.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
