12
Introduction
Set the video setting switches on the camera unit
before mounting it.
To set the switches, use a fine-tipped screwdriver.
A
[IRIS LEVEL] Iris level adjustment
For adjusting the level of the automatic
aperture control lens. This adjustment only
needs to be made when required. Use this to
accommodate particular shooting conditions.
To darken image: Counterclockwise (L side)
To brighten image: Clockwise (H side)
NOTE:
Prior to adjusting the aperture level, ensure to
set the 1 [AGC] Switch of the function
selection switch
G
to
A
OFF
B
. Otherwise, when
the level is turned too far toward L, the AGC
function activates increasing sensitivity and
the picture may look uneven.
B
[ZOOM/FOCUS, MEMORY] zoom, focus
adjustment switches/position memory
button
Use the [
J
TELE] and [
K
WIDE] switches to
zoom, and the [
H
FAR] and [
I
NEAR] switches
to adjust focus. (
A
pg. 25)
Press the [MEMORY] button to register the
position. (
A
pg. 25)
C
[ALARM POSITION] status indication lamp
Light off
: Registration of home
position is enabled
Light on (red)
: Lens initializing.
Light on (green): Registration of alarm
position is enabled
Blinking (green) : Position memory registration
mode
N
memory
registration completed
(
A
pg. 25)
D
[POSITION SELECT] POSITION SELECT
button
Press this button to switch between the home
and alarm positions. Display on the status
indication lamp
C
will change accordingly.
(
A
pg. 25)
E
[RESET/SPOT] RESET/SPOT button
When this button is pressed, the value of the
white balance or phase adjusted manually is
reset to the default value.
●
When the 2 [SELECT] switch is set to
[WHT.BAL.], the white balance is reset to the
default value.
When the switch is set to PHASE, the phase
is reset to the default value.
●
When setting to SPOT:
When this button is pressed, white-spots are
corrected.
For instructions on correcting white-spots, see
A
White-spot correction
B
(
A
pg. 28).
F
[R/B, +/
-
] R/B, +/
-
adjustment button
This button is pressed when manually
adjusting the white balance or when adjusting
the vertical phase of the line lock.
The function of this button is selected using
the 2 [SELECT] switch.
●
When manually adjusting the white balance:
Press the R button to increase the red tint and
decrease the blue tint.
Press the B button to increase the blue tint
and decrease the red tint.
●
When adjusting the phase:
Press the + or
-
button to adjust the phase.
G
Function selection switches
1.
[AGC] Auto-gain control switch.
Setting this switch to
A
ON
B
automatically
increases the sensitivity even when the
brightness of the subject is insufficient.
(Default setting: ON)
Setting the Lens and
Switches (TK-C215V12)
B
RESET/[SPOT]
LL
PHASE
R
WHT.BAL.
H
L
IRIS
LEVEL
ZOOM/FOCUS FAR
WIDE
NEAR
POSITION SELECT
POSITION
ALARM
[MEMORY]
2
4
1
2
3
4
5
6
7
8
TELE
A
G
B
C
D
E
F
WHT.BAL.
PHASE
RESET/SPOT
8
TRIGGER
STATE
ALARM
7
OFF
ON
DAY/NIGHT
6
5
OFF
BLC
ON
4
ON
ON
AGC
OFF
OFF
MANUAL
3
ATW
2
LL
SYNC
INT
1
WHT.BAL.
SELECT
RESET
SPOT
Function selection switch setting table
(Items in bold are factory position)
TK-C215V4_V12_EN.book Page 12 Wednesday, August 2, 2006 1:18 PM
