20
English
¶
Speaker distance
—FRONT L DIST, FRONT R DIST,
CENTER DIST, SURR L DIST, SURR R DIST
Set the distance from the listening point within the range of
0.3 m (1 ft) to 9.0 m (30 ft), in 0.3 m (1 ft) intervals.
• When shipped from the factory, distance for each speaker is
set to “3.0m (10FT).”
Notes:
• You cannot set the speaker distance for the speakers you have
selected “NONE.”
• For RX-6042S: This setting is not valid for “DVD MULTI.”
Ex. In the above case, set the speaker distance as follows:
Front speakers:
3.0m (10FT)
Center speaker:
3.0m (10FT)
Surround speakers:
2.7m (9FT)
Setting the Bass Sounds
You can adjust subwoofer and bass sounds precisely according to
your preference.
¶
Subwoofer output
—SUBWOOFER OUT
You can select the type of the signal which can be transmitted
through the subwoofer. In other words, you can determine
whether or not the bass elements of the front speaker channels
are transmitted through the subwoofer regardless of the front
speaker size setting (either “SMALL” or “LARGE”).
Select one of the following:
SWFR LFE:
Select to emit only the LFE signals (while
playing Dolby Digital and DTS software) or the
bass elements of the “SMALL” front speakers
(while playing any source other than the above).
SWFR LFE+MAIN:
Select to always emit the bass elements of
the front speaker channels (MAIN). While
playing Dolby Digital and DTS software, the
bass element and the LFE signals are both
emitted.
Note:
If you have selected “SUBWOOFER NO” for the subwoofer, this
function is not available.
Setting the Speakers
To obtain the best possible surround effect from the Surround and
DSP modes, register the setting about the speaker arrangement after
all connections are completed.
• If you have used Quick Speaker Setup on page 18, this setting is
not required.
¶
Subwoofer setting
—SUBWOOFER
Select whether you have connected a subwoofer or not.
SUBWOOFER YES:
Select when a subwoofer is connected.
SUBWOOFER NO:
Select when no subwoofer is used.
Note:
If you have selected “SUBWOOFER NO” for the subwoofer, you
cannot use the SUBWOOFER OUT ON/OFF button on the front
panel.
¶
Speaker size
—FRNT SPEAKERS, CNTR SPEAKER,
SURR SPEAKERS
Select the size for each connected speaker.
LARGE:
Select when the speaker size is relatively large.
SMALL:
Select when the speaker size is relatively small.
NONE:
Select this when you have not connected a
speaker. (Not selectable for the front speakers)
Notes:
• Keep the following comments in mind as reference when
adjusting.
– If the size of the cone speaker unit built in your speaker is
larger than 12 cm, select “LARGE,” and if it is smaller than
12 cm, select “SMALL.”
• If you have selected “SUBWOOFER NO” for the subwoofer
setting, you can only select “LARGE” for the front speakers.
• If you have selected “SMALL” for the front speakers, you cannot
select “LARGE” for the center and surround speakers.
Setting the Speaker Distance
The distance from your listening point to the speakers is another
important element to obtain the best possible sound of the Surround
and DSP modes. Set the distance from your listening point to the
speakers.
By referring to the speaker distance setting, this unit automatically
sets the delay time of the sound through each speaker so that sounds
through all the speakers can reach you with the same timing.
• If you have used Quick Speaker Setup on page 18, this setting is
not required.
¶
Measuring unit
—DISTANCE UNIT
Select which measuring unit you use.
UNIT METER:
Select to set the distance in meters.
UNIT FEET:
Select to set the distance in feet.
Basic Settings
2.1 m
(7 ft)
2.4 m
(8 ft)
2.7 m
(9 ft)
3.0 m
(10 ft)
3.3 m
(11 ft)
C
L
R
LS
RS
18-22_5042&6042[US]f.p65
04.2.4, 5:45 PM
20
