JVC RK-C42WBT3 Assembly And Mounting Instructions Download

Page: 9 / 16

<Instructions for Assembly, cont’d>

Adjusting the Angle of the Plasma Display

＊

The angle of the Wall Mounting Unit can be adjusted to 0

, 5

, 10

, 15

, and 20

1. Adjust the angle of the plasma display.

Brace the upper middle part of the plasma display with one hand and push the Angle Adjustment Lever to the

left with the other hand. The plasma display will tip forward. Release the Angle Adjustment Lever when the

desired angle setting is reached.

Caution

Grip the plasma display firmly while adjusting the angle, as the display could tip over and cause

injury.

2. Fix the Angle Adjustment Lever.

Once the plasma display has been set at the desired angle, fasten the Angle Adjustment Lever with the screw

(M5X20)

＊

Check to make sure that the Angle Adjustment Lever is securely fastened and the plasma display does not

rattle and loose.

＊

Note: do not fasten the Angle Adjustment Lever if the power cord or system cables have yet to be attached.

Screw (M5X20) x 1

Angle Adjustment
Lever

Summary of Contents for RK-C42WBT3

















Search results

Summary of Contents for RK-C42WBT3

Reviews:

Related manuals for RK-C42WBT3

Brands by name

Popular brands

JVC RK-C42WBT3, Assembly And Mounting Instructions

Search results

Summary of Contents for RK-C42WBT3

Reviews:

Related manuals for RK-C42WBT3

Brands by name

Popular brands