20
English
To tune in a preset station
On the front panel:
1. Turn SOURCE SELECTOR to
select the band (FM or AM —
MW/LW).
The last received station of the selected band
is tuned in.
2. Press TUNER PRESET.
3. Turn MULTI JOG until you find
the channel you want.
• Turning it clockwise increases the channel
numbers.
• Turning it counterclockwise decreases the
channel numbers.
From the remote control:
1. Press FM/AM.
• Each time you press the button, the band
alternates between FM and AM (MW/LW).
2. Press the 10 keys to select a preset
channel number.
• For channel number 5, press 5.
• For channel number 15, press +10 then 5.
• For channel number 20, press +10 then 10.
• For channel number 30, press +10, +10,
then 10.
Note:
When you use the 10 keys on the remote control, be sure that they
are activated for the tuner, not for the CD and others. (See page 45.)
Selecting the FM Reception Mode
When an FM stereo broadcast is hard to
receive or noisy
You can change the FM reception mode while receiving an FM
broadcast.
• You can store the FM reception mode for each preset station.
Press FM MODE on the front panel or on the remote control.
• Each time you press the button, the FM reception mode alternates
between “AUTO MUTING” and “MONO.”
AUTO MUTING: When a program is broadcasted in stereo,
you will hear stereo sound; when in monaural, you will
hear monaural sounds. This mode is also useful to
suppress static noise between stations. The AUTO
MUTING indicator lights up on the display.
MONO: Reception will be improved although you will lose the
stereo effect. In this mode, you will hear noise while
tuning into the stations. The AUTO MUTING indicator
goes off on the display.
SOURCE SELECTOR
TUNER PRESET
MULTI JOG
Note:
When using the FM MODE button on the remote control, be sure that
the 10 keys are activated for the tuner, not for the CD and others.
(See page 45.)
Assigning Names to Preset Stations
You can assign a name of up to four characters to each preset
station. When a preset station is tuned in, its assigned name will
appear on the display.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You can use the following characters: Space (_), A – Z, and 0 – 9.
On the front panel ONLY:
1. Tune in a preset station.
See the left.
2. Press TUNER (/SEA) MEMORY.
The preset channel number starts flashing for
about 10 seconds.
• If you turn MULTI JOG while the preset channel number is
flashing, you can change the preset channel number.
3. Press TUNER PRESET, while the
preset channel number is flashing.
The first character position starts flashing.
4. Turn MULTI JOG to select the
first character, while the first
character position is flashing.
5. Press TUNER PRESET, while a
character you want is flashing.
The next character position starts flashing.
6. Repeat steps 4 and 5 to enter up to four
characters.
7. Press TUNER (/SEA) MEMORY
while the last selected character is
flashing after you have assigned a
name.
To erase the input characters
Insert spaces using the same procedure described above.
TUNER
/SEA
MEMORY
TUNER PRESET
MULTI JOG
TUNER PRESET
TUNER
/SEA
MEMORY
FM MODE
On the front panel
SUBWOOFER
0
FM MODE
On the remote control
CNTR TONE
CENTER
TEST
REAR-L
EFFECT
REAR-R
SEA MODE
SUBWOOFER
RETURN
FM MODE
1
2
3
4
5
6
7
/P
8
9
10
0
+10
100+
MENU
ENTER
FM/AM
EN19_23.RX-7000R[E]/f
00.4.24, 3:01 PM
20
Summary of Contents for RX-7000RBK
Page 26: ...1 26 RX 7000RBK MEMO ...
Page 44: ...RX 7000RBK 3 2 MEMO ...
