JVC RX-7001PGD Service Manual Download

Page: 125 / 137

English

Tuner

You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):

FM/AM

Alternates between FM and AM.

After pressing FM/AM (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations:

1 – 10, +10

Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.

TUNING UP/TUNING DOWN

Tunes into stations.

FM MODE

Changes the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):

SURROUND ON/OFF

Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, DTS
Digital Surround and MPEG
Multichannel.

SURROUND MODE

Selects the DSP modes.

After pressing SOUND (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations:

SEA MODE

Changes the SEA modes.

SUBWOOFER – / +

: Adjusts the subwoofer output level.

CENTER – / +

Adjusts the center speaker output level.

REAR•L – / +

Adjusts the left rear speaker output level.

REAR•R – / +

Adjusts the right rear speaker output level.

EFFECT

Selects the effect level.

TEST

Turns on or off the test tone output.

Note:

After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.

CD player

After pressing CD (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations on
the CD player:

PLAY

Starts playing.

Returns to the beginning of the current (or

previous) track.

Skips to the beginning of the next track.

STOP

Stops playing.

PAUSE

Pauses playing. To release it, press PLAY.

1 – 10, +10

Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:

To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the

COMPU LINK-3 (SYNCHRO) jacks (see page 35) in
addition to the connections using cables with RCA pin plugs
(see pages 5 and 6).

• Aim the remote control directly at the remote sensor on the

receiver.

• If you use the buttons on the front panel or the menu

function to choose a source, the remote control will not
operate that source. To operate a source with the remote
control, the source must be selected using source selecting
buttons on the remote control.

• To operate the cassette deck or MD recorder using the

COMPU LINK remote control system, set the source name
correctly. (See page 13.)

• Refer also to the manuals supplied with your components.

Check to see if the remote
control mode selector is set
to the correct position.
To operate the audio
system, TVs, VCRs, and
DVD players, set it to
“AUDIO/TV/VCR.”

RM-SRX7001P REMOTE CONTROL

CONTROL

CHANNEL

VOLUME

TV VOL

TUNING

STOP

PAUSE

FF/

/REW

VCR

TV/VIDEO