25
Changing the Display Brightness
You can dim the display.
Press DIMMER.
• Each time you press the button, the brightness level of the display
changes as follows:
Note:
Even though the dimmer is in use, the display brightens for a while
when you operate the receiver (except when changing the source).
Turning Line Direct On and Off
You can enjoy the sound closer to original source by skipping the
sound adjustments such as Midnight mode (see page 38), speaker
output level adjustments (see page 44) and Parametric Equalizer (see
page 44). You can only adjust the volume level while Line Direct is
in use.
• You have to make this setting for each source.
Press LINE DIRECT.
• Each time you press the button, Line Direct turns on and off.
– When Line Direct turns on, “LINE DIRECT” appears in the
main display.
Notes:
• This function is applied only to the main room sources.
• If you turn on Line Direct while using the Surround and DSP
modes, the effect changes as follows:
• If you turn on Line Direct, CC Converter (see the right column) is
canceled.
• Turning off Line Direct activates the sound adjustments previously
selected such as Midnight mode, speaker output level adjustments
and Parametric Equalizer.
• If you turn off Line Direct while listening to an analog source,
muting time* will be a little longer. (* The period during which no
sound comes out.)
On the remote control
DIMMER
On the remote control
On the unit
(inside the front door)
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
LINE DIRECT
Ex. When the source is “VIDEO.”
Mode
Surround
DSP
Input
Analog
Not valid
Not valid
Digital
Valid
Not valid
Making Sounds Natural
JVC’s CC (Compensative Compression) Converter eliminates jitter
and ripples, achieving a drastic reduction in digital distortion by
processing the digital music data in 24 bit–quantization and by
expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz
signals)/192 kHz (for fs 48 kHz signals).
By using the CC Converter, you can obtain a natural sound field
from any source.
Press CC CONVERTER so that the CC
CONVERTER lamp lights up.
• Each time you press the button, CC Converter turns on and off (the
lamp goes off) alternately.
Note:
• This function is applied only to the main room sources.
• You cannot use this function while Line Direct or THX Surround is in
use. If you turn on Line Direct or THX Surround while this function
is in use, this function will be canceled.
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks
or the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the MD recorder or DBS tuner as the source.
On the unit ONLY:
When changing the source name from “TAPE” to
“MD”:
1. Press TAPE/MD.
2. Press and hold TAPE/MD until
“ASSGN. MD” appears on the display.
When changing the source name from “TV ” to
“DBS”:
1. Press TV/DBS.
2. Press and hold TV/DBS until “ASSGN.
DBS” appears on the display.
To change the source name to “TAPE” or “TV,” repeat the same
procedure above — press and hold TAPE/MD to select “TAPE,” or
press and hold TV/DBS to select “TV” in step 2.
• While selecting “DBS” as the sub-room source, you cannot
change the source name to “TV.”
CC CONVERTER
CC CONVERTER
On the unit
On the remote control
TAPE/MD
On the unit
D I M M E R
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
TV/DBS
L
ANALOG
SPEAKERS
VOLUME
1
SUBWFR
R
dB
LINE DIRECT
Dimmer
Much dimmer
Canceled
(Normal display)
EN17-30_RX-DP10VBK[J]_f
01.6.19, 1:13 PM
25
