21
5-2 Contents of the Function Menu Switches
5 SETTING OF THE FUNCTION MENU SWITCHES
[ ]: Factory setting
Function
Screens
Items
Set values
VTR mode 1
INDEX
[OFF]
setting
SEARCH
ON
Enables or disables the Index Search function.
OFF : The index search function is disabled.
ON
: When an alarm-recorded tape is put in the FF or REW Shuttle Search
mode, the VCR searches for the nearest recorded index code (VISS
signal) and engages playback at the indexed position.
When an alarm-recorded tape is fast-forwarded or rewound, the VCR
searches for the nearest index code and enters the Stop mode at the
indexed position.
CAMERA SW
[OFF]
1 FIELD
1 FRAME
*The set timing may differ greatly from the actual timing.
Set the tape end signal output timing. When the tape reaches the specified
position, the following signals are output.
• The tape end signal is output from the rear panel’s [TAPE END] terminal.
• The series recording signal is output from the rear panel’s [SERIES OUT]
terminal (with the <TERMINAL SEL 1> function menu switch set to “SERIES”).
• The tape end buzzer sounds (with the <TAPE END BUZZER> function menu
switch set to “ON”)
• “End” is shown on the counter display.
OFF.
: When the tape ends
180S.
: When the tape remaining time is about 3 minutes during 2H mode.
When the tape remaining time is about 9 minutes during 6H mode.
When the tape remaining time is about 18 minutes during L12H mode.
When the tape remaining time is about 36 minutes during L24H mode.
360S
: When the tape remaining time is about 6 minutes during 2H mode.
When the tape remaining time is about 18 minutes during 6H mode.
When the tape remaining time is about 36 minutes during L12H mode.
When the tape remaining time is about 72 minutes during L24H mode.
TERMINAL
[WARN.]
SEL 2
REC
Select the signal to be input or output to the [SERIES/CLOCK IN·OUT]
terminals on the rear panel.
SERIES : Set to this position to input or output a series recording signal.
EXT
: Set to this position to start or stop the recording with the VCR
activation signal input from an external control device.
C.ADJ
: Set to this position to input or output a clock reset signal.
REC REMAIN
[OFF]
180S
360S
Select the signal output from the rear panel’s [WARNING/REC OUT] terminal.
WARN. : Set to this position to output a warning signal. The warning signal is
output if an abnormality occurs in tape transport or mechanism
operation.
REC
: Set to this position to output a recording mode signal (+12 V) in the
Record mode.
TERMINAL
[SERIES]
SEL 1
EXT
C.ADJ
Turns summer time compensation on or off.
OFF : Clock is not adjusted for summer (daylight saving) time.
ON
: Clock is adjusted for summer (daylight saving) time.
VTR mode 2
SUMMER TIME
[OFF]
setting
ON
Turns the warning buzzer on or off.
OFF : The buzzer does not sound.
ON
: The buzzer sounds.
WARNING
[OFF]
BUZZER
ON
Turns the Tape End buzzer on or off.
OFF : The buzzer does not sound at tape end.
ON
: When the tape reaches the position set with the <REC REMAIN> menu
function switch during recording (tape end, or about 3 minutes or 6
minutes before the tape ends during 2H mode ), a buzzer sounds.
To stop the buzzer sound, press the [REW] button, [EJECT] button or
[POWER] button.
When the mode is changed, the buzzer sound stops.
TAPE END
[OFF]
BUZZER
ON
Sets the camera switching interval for output to an external sequential switcher
during recording.
OFF
: No camera switching signal is output.
1 FIELD : Set to this position to switch the camera every 1 field.Signals are
output every 1 frame when recording in the 6H mode even when this
is set to 1FIELD.
1 FRAME : Set to this position to switch cameras every 1 frame.
Summary of Contents for SR-L910UA
Page 4: ...4 ...
