Masterpage:Right+
EN
53
Filename [SR-MV30U_07VCR Operation.fm]
Page 53
April 1, 2004 2:13 pm
OPERATIONS ON VCR DECK
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer-record the program.
1
Load a cassette with the record safety tab intact.
2
Press
VCR/DVD
repeatedly so that the VCR lamp lights up on
the unit.
3
Press
PROG/CHECK
to access the
Program Check screen.
4
Press
rt
to select the blank
number, then press
ENTER
. The
program screen appears.
5
Press
w e
to select “START”, then
press
rt
to set the desired start time.
●
Each press of
rt
advances/goes back
the start time in 1-min. increments.
●
To advance/go back the start time in
30-min. increments, press and hold
rt
.
6
Press
w e
to select “STOP”, then press
rt
to set the desired
stop time.
●
Each press of
rt
advances/goes back the stop time in 1-min.
increments.
●
To advance/go back the stop time in 30-min. increments, press and
hold
rt
.
7
Press
w e
to select “DATE”, then press
rt
to set the desired
date.
●
The current date appears on the TV screen. The date you enter
appears in its place.
8
Press
w e
to select “CH”, then press
rt
to select the desired
channel.
9
Press
REC MODE
to select the desired recording mode. Or
press
w e
to select “SP/EP”, then press
rt
to select the desired
recording mode.
10
Press
ENTER
to access the Program Check screen.
11
Press
PROG/CHECK
to complete timer programing.
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM NOT
COMPLETED PROGRAM OVERLAP” appears on the TV screen,
see page 54.
●
To program another timer, repeat steps
–
12
Press
VCR TIMER
(
#
) to engage the unit’s timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. When the DVD deck is in timer standby
mode, the unit is automatically turned off.
●
To disengage the timer mode, press
VCR TIMER
(
#
) again.
NOTES:
●
To Timer-Record Weekly Or Daily Serials:
— anytime during steps
through
, press
number key “9”
for
weekly serials or
number key “8”
for daily serials (Monday – Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
●
You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (
●
In case of a power failure after programing, the unit’s memory backup
keeps your selections for approximately 5 seconds.
●
Programs that start after midnight must have the next day’s date.
●
To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to “Manual Timer
Programing” (
Manual Timer Programing
●
Make sure that the unit’s built-in clock is set properly.
●
Turn on the unit.
●
Turn on the TV and select the video channel (or AV mode).
●
Slide the
TV/CABLE/DBS/DVD
switch to
DVD
.
1
4
7
2
5
8
0
3
6
9
PROG/CHECK
ENTER
VCR TIMER (
#
)
rtw
e
VCR/DVD
0 – 9
REC MODE
(PROG/CHECK) TO NEXT
PR START
STOP
CH
DATE
1
8:00P
10:00
12
12/24
2
10:00A
10:45 40
12/25
3
11:30P
1:00 125
12/25
4
5
6
7
8
PROGRAM 4
START
STOP
– –:– –AM
– –:– –AM
DATE
CH SP/EP
– –/– –/– –
– – –
SP
PRESS (
RTYU
, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROG/CHECK) TO END
SR-MV30U_07VCR Operation.fm Page 53 Thursday, April 1, 2004 2:13 PM
