Masterpage:Left-FullCol
60
EN
Filename [SR-V10E4-EN.fm]
Page 60
August 8, 2002 5:41 pm
TROUBLESHOOTING (cont.)
RECORDING
TIMER RECORDING
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Recording cannot be started.
●
There is no cassette loaded.
Load a cassette with the record safety tab
intact. If the tab has been removed, set
“REC SAFETY” to “OFF” (
墌
pg. 48).
●
The loaded cassette has had its record
safety tab removed and “REC SAFETY”
is set to “ON”.
Set “REC SAFETY” to “OFF” (
墌
pg. 48),
or using adhesive tape, cover the hole
where the tab was removed.
2. TV broadcasts cannot be recorded.
●
“L-1”, “F-1”, “S-1” or “S-2” has been
selected as the input mode.
Set to the desired channel.
3. Tape-to-tape editing is not possible.
●
The source (another video recorder,
camcorder) has not been properly
connected.
Confirm that the source is properly
connected.
●
All necessary power switches have not
been turned on.
Confirm that all units’ power switches are
turned on.
●
The input mode is not correct.
Set the input mode to “L-1”, “F-1”, “S-1”
or “S-2”.
4. Camcorder recording is not possible.
●
The camcorder has not been properly
connected.
Confirm that the camcorder is properly
connected.
●
The input mode is not correct.
Set the input mode to “L-1”, “F-1”, “S-1”
or “S-2”.
5. The recorder automatically rewinds
the tape to the beginning.
●
The end of the tape was reached during
recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Timer recording won’t work.
●
The clock and/or the timer have been set
incorrectly.
Re-perform the clock and/or timer
settings.
●
The timer is not engaged.
Press
#
and confirm that “
#
” is displayed
on the front display panel.
2. Timer programming is not possible.
●
Timer recording is in progress.
Timer programming can’t be performed
while a timer recording is in progress.
Wait until it finishes.
3. “
#
” on the front display panel won’t
stop blinking.
●
The timer is engaged but there’s no
cassette loaded.
Load a cassette with the record safety tab
intact. If the tab has been removed, set
“REC SAFETY” to “OFF” (
墌
pg. 48).
4. “
#
”, “
䡬
” and “
$
” on the front
display panel won’t stop blinking.
●
The loaded cassette has had its record
safety tab removed and “REC SAFETY”
is set to “ON”.
Set “REC SAFETY” to “OFF” (
墌
pg. 48),
or using adhesive tape, cover the hole
where the tab was removed.
●
The end of the tape was reached during
timer recording.
The programme may not have been
recorded in its entirety. Next time make
sure you have enough time on the tape to
record the entire programme.
5. “
#
” blinks for 10 seconds and the
Timer mode is disengaged.
●
#
has been pressed when there are no
programs in memory, or the timer
record information has been
programmed incorrectly.
Check the programmed data and re-
program as necessary, then press
#
again.
6. The S
HOW
V
IEW
system does not
timer-record properly.
●
The recorder’s channel positions have
been set incorrectly.
Refer to “Guide Program Number Set”
(
墌
pg. 49) and re-perform the procedure.
SR-V10E1-EN.book Page 60 Monday, August 19, 2002 10:20 AM
