background image

CONTENTS

Important Safety Precautions

1.

DISASSEMBLY ............................................................................................................................................................... 1-1

3.

ADJUSTMENT ................................................................................................................................................................ 3-1

4.

CHARTS AND DIAGRAMS ............................................................................................................................................ 4-1

5.

PARTS LIST .................................................................................................................................................................... 5-1

The following table indicate main different points between models GR-DX75EK, GR-DX75EX, GR-DX75EY, GR-DX75EZ, GR-
DX95EK, GR-DX95EX, GR-DX95EY and GR-DX95EZ.

DIFFERENT LIST

DIFFERENT TABLE OF FEATURE

Notes: Mark 

 is same as left.

MODEL

GR-DX75EK

ITEM

LCD MONITOR

2.5 INCH

3.0 INCH

AC CORD

BS PLUG

CEE PLUG

BS PLUG

CEE PLUG

GR-DX75EX GR-DX75EY GR-DX75EZ GR-DX95EK GR-DX95EX GR-DX95EY GR-DX95EZ

Summary of Contents for GR-DX75EK

















Reviews: