background image

 
 
 
 

 CAUTION                                                        

1.  To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust 

air into spaces within walls or ceilings or into attics, crawl spaces, or garages.   

2.  Take care when using cleaning agents or detergents.   
3.  Avoid using food products that produce flames under the Range Hood.   
4.  For general ventilating use only. Do not use to exhaust hazardous or explosive materials and 

vapors.  

5. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, 

construction dust, etc. off power unit.   

6.  Your hood motor has a thermal overload which will automatically shut off the motor if it becomes 

overheated. The motor will restart when it cools down. If the motor continues to shut off and 
restart, have the hood serviced.   

7.  For best capture of cooking impurities, the bottom of the hood should be a minimum of 24" and a 

maximum of 33" above the cooking surface.   

8.  Two installers are recommended because of the large size and weight of this hood.   
9.  This product is equipped with a thermostat which may start blower automatically. To reduce the 

risk of injury and to prevent power from being switched on accidentally, switch power off at 
service panel and lock or tag service panel.   

10.  Use with approved cord-connection kit only.   
11.  Please read specification label on product for further information and requirements.   

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for K1003














Reviews: