background image

KTI63421 2  05/01/19

This is the safety alert symbol. It is used to alert you to 
potential personal injury hazards. Obey all safety messages 
that follow this symbol to avoid possible injury or death.

             

 

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING

PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of 
the device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost 
or not legible, contact K-Tool International for replacements. If the operator is not fluent in English, the product and safety instructions 
shall be read to and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making 
sure that the operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical 
means, but only by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel  
involved in the use and operation of the equipment who are careful, competent, trained, and qualified in the safe operation of  
the equipment and its proper use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly  
secured loads, overloading, off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for  
which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

  •  Read, study, understand & follow all instructions before using.
  •  User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
  •  Inspect crane before each use. Do not use if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or    
    unstable due to loose or missing hardware or parts. Take corrective action before using.
  •  Never get under the load being lifted or suspended.
  •  Use only on a hard level surface.
  •  Do not raise the boom if the crane is equipped with a foldable or storable leg feature and the legs are in the upright position.
  •  Use only slings or chains with a rated capacity greater than the weight of the load being lifted.
  •  Do not exceed rated capacity.
  •  Do not lift or move a load that has a center of gravity extending beyond the front wheels.  
  •  Do not allow load to swing or drop violently while raising, lowering or moving.
  •  Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the  

 

    manufacturer's authorized representative.
  •  Before moving, lower load to the lowest possible point.
  •  Apply the load restraint to the engine before transporting. See operating instructions in manual.
  •  No alterations shall be made to this product and do not use any unapproved attachments.
  •  Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,  
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS  
SITUATIONS could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

WARNING INFORMATION

WARNING: 

This product can expose you to chemicals including nickel, which is known to the State of California to 

cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Summary of Contents for KTI63421




















Reviews: