background image

KTI63421 5  05/01/19

PROBLEM: POOR LIFT PERFORMANCE OR WILL NOT LIFT MAXIMUM HEIGHT.
POSSIBLE CAUSE:

 

Hydraulic fluid low.

ACTION:

 

Place jack in its upright position. Retract the ram. Remove the reservoir fill plug. Add only high quality hydraulic jack oil  

up the bottom level of the hole. Reinstall fill plug. Purge air from system according to steps "a" through "d" in the "SETUP  
INSTRUCTIONS" section of this manual.

POSSIBLE CAUSE:

 

Air trapped in hydraulic system.

ACTION:

 

Purge air from the system. See steps "a" through "d" in the "SETUP INSTRUCTIONS" section of this manual.

K-Tool International warrants that all jacks and service-related equipment will be free from defects in material and workmanship for a 
period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser only. If any jack or 
service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s option, without 
charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any equipment which 
has been altered or used with special attachments other than those recommended. This warranty does not cover repairs made by 
anyone who is not a K-Tool International Professional Lifting Equipment Authorized Repair Center.

All HD and XD jacks or service-related equipment will be replaced or repaired at K-Tool International’s option during the 2 year warranty 
period.

During the 2 year warranty period, all alleged defective products must be shipped, freight prepaid, along with proof of date-of-purchase, 
to your nearest K-Tool International Professional Lifting Equipment Authorized Warranty Center. Be certain to include your name, 
address and phone number along with proof-of-purchase information, and a brief description of the alleged defect. The product will be 
returned to the customer, freight prepaid.

Many alleged defectives may simply be handled by calling your nearest Service Center for parts. See pages 17 - 19 for a listing of 
authorized warranty service centers.

In no event shall K-Tool International be liable for incidental or consequential damages. The liability on any claim for loss or damage 
arising out of the sale, resale or use of a jack or related service equipment, shall in no event exceed the purchase price. SOME STATES 
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION 
MAY NOT APPLY TO YOU.

THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED IN CONNECTION WITH THE SALE OF K-TOOL 
INTERNATIONAL PROFESSIONAL LIFTING EQUIPMENT. ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE 
TO STATE.

WARRANTY HANDLING PROCEDURES AND GUIDELINES FOR HD AND XD LIFTING EQUIPMENT

Summary of Contents for KTI63421




















Reviews: