background image

2

  GENERAL SAFETY RULES

  Jack use and care

  Inspection

GENERAL SAFETY RULES

IMPORTANT SAFETY CONSIDERATIONS

WARNING: Read and understand all instructions. 

Failure to follow all instructions listed below may 

result in serious injury.

WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot 

cover all possible conditions or situations that could occur. 

It must be understood by the operator 

that common sense and caution are factors that cannot be built into this product, but must be supplied by 

the operator.

CAUTION: Do not allow persons to operate or assemble this jack until they have read this manual 

and have developed a thorough understanding of how the jack works.

DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL.

To maintain the service jack and user safety, the responsibility of the owner is to read and follow these 

instructions.

• Inspect the service jack for proper operation and function.

• Keep instructions readily available for equipment operators.

• Make certain all equipment operators are properly trained; understand how to safely and correctly operate 

the unit.

• Allow unit operation only with all parts in place and operating properly.

• Use only genuine replacement parts.

• Service and maintain the unit only with authorized or approved replacement parts; negligence will make the 

jack unsafe for use and void the warranty.

• Carefully inspect the unit on a regular basis and perform all maintenance as required.

• Store these instructions in the handle of your jack.

• Keep all decals on the unit clean and visible.

• Inspect the jack carefully before each use. Ensure the jack is not damaged, excessively worn, or missing 

parts.

• Do not use the jack unless it is properly lubricated.

• Using a jack that is not in good clean working condition or properly lubricated may cause serious injury.

• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.

• 

Do not modify the Jack in any way.

 Unauthorized modification may impair the function and/or safety and 

could affect the life of the equipment. There are specific applications for which the Jack was designed.

• 

Always check for damaged or worn out parts before using the jack.

 Broken parts will affect the jack 

operation. Replace or repair damaged or worn parts immediately.

• 

Store the jack.

 When jack is not in use, store it in a secure place out of the reach of children. Inspect it for 

good working condition prior to storage and before re-use.

• 

Not for use by children

 or people with reduced mental capacity.

• 

Do not use under the influence of drugs or alcohol.

• 

Ensure children and other bystanders are kept at a safe distance when using product.

Summary of Contents for XD KTI-63213A











Reviews: