Kaabo Skywalker 10, User Manual

19

20

DISPLAY &

KEY SETTINGS

3. Power Button. To turn the scooter on or off press button for 2 seconds.

4. Accelerator. Pull to accelerate. The stronger you pull, the faster it

accelerates. The scooter is delivered in “Non-Zero Start” setting

(Kick-And-Go is ON), i.e. the accelerator only works if the scooter is

already in motion.

5. Mode Button. Press to select various display options:

Detailed  P-settings  mode. 

To  access  P-settings  to  make  various  advanced 

changes, press POWER [3] and MODE [5] simultaneously for 2 seconds.

Cycle through the P-settings using the MODE button. To select a P-setting in 

order to make changes press the POWER button. Change the value (up or 

down) using the MODE (Up) and POWER (Down) buttons. To return to the 

P-settings menu after changing a value, wait 2 seconds. To return to operating

mode, wait a further 2 seconds. Only 

COMMENT

MODE

TIME

Time since powering on the scooter.

TRIP

Distance travelled since powering on the scooter. 

ODO

Total distance travelled.

VOL

Current battery voltage.

CH2:00

Charging mode. Time (2 hours) scooter stays ON (overrides auto-switch off)

 so you can use display’s USB port to charge e.g. your phone.

P-SETTINGS

P0

Tire diameter . 

P1

Controller shut-down voltage. Default set to 52V . 

P2

Motor magnetic pole setting. Default is 30. Do not change. 

P3

Speed signal selection. Default is 0. Do not change.

P4

Distance / speed unit. 0=km, 1=miles

P5

Start setting. 1=non-zero start (Kick-and-Go), accelerator won’t work if scooter not in 

motion; 0=immediate start (CAUTION while using this!)

P6

Cruise control. 0=cruise control OFF, 1=cruise control ON.

P7

Initial acceleration. 0=strong, 1=soft.

P8

Electric (regenerative) braking (E-ABS). 0=E-ABS off, 1=E-ABS on

P9

Speed limit as % of top speed, i.e. 100=no speed limit.

PA

Clear total distance travelled (ODO).

PB

Scooter auto-turn off time in minutes.

PC

Display brightness (1=low, 3=high)

Driving Mode Selection

Located underneath the main display on the right side of 

the  handle  bar  you  can  find  two  switches  to  configure 

driving modes:

The  ECO/TURBO  switch  regulates  the  power  of  your  scooter.  By  pressing 

down the button, ECO mode is activated which will reduce torque and top 

speed to maximize range. When the button is not pressed, TURBO mode is 

activated and there is no restriction of power.  
The SINGLE/DUAL switch toggles single or dual motor drive. By pressing down 

the button DUAL motor drive is activated. When the button is not pressed, 

SINGLE (rear) motor drive is activated.
For Maximum range, select ECO mode and SINGLE motor drive. For maximum 

power and speed, select TURBO mode and DUAL motor drive.

Display Settings

Scooter is equipped with the following display:

Gear change. 

To  change  the  gear  (1=slow,  2=medium,  3=fast),  while  the 

scooter is powered ON, press the POWER button to enter gear setting mode. 

Press MODE to switch between gears. To return to operating mode either 

press POWER or wait for 2 seconds.

1. Speedometer. Shows the speed at which you are travelling.

2. Battery Indicator. Charge your scooter frequently, do not let it run out

     of battery. As a rough guideline, charge at or below 2 bars.