background image

ISED Statement

English:

 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, 

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the 

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired 
operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux 
RSS exemptés de licence d'Innovation, Sciences et Développement économique Canada. 

L'exploitation est soumise aux deux conditions suivantes :

(1) Cet appareil ne doit pas provoquer d'interférences.

(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de 
provoquer un fonctionnement indésirable de l'appareil.

l'appareil numérique du ciem conforme canadien peut  - 3 (b) / nmb  - 3 (b).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and 
compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure  and 
compliance.

cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 

102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données 
canadiennes sur l'exposition aux champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled 
environment.

Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies pour un 
environnement non contrôlé.

This equipment should be installed and operated with minimum distance 20cm between the radiator & 
your body.

Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et 
votre corps.

Summary of Contents for KA251-Z
























Reviews: