background image

9

B

ASIC

 L

OCK

 O

PERATIONS

For the complete Cencon lock and software operating instructions in FLM, Route, 
and Bank modes, please see the Cencon Reference Manual on the documentation 
section at www.kaba-mas.com.

Opening Lock in Shelved Mode

Each lock is shipped from the factory in Shelved Mode. The “one time only” 
combination feature is not available when the lock is shelved. Instead, the 
Shelved Mode combination is used to open the lock. The default Factory 
Combination is set to 50-25-50. The default combination may be changed, 
in which case the new combination would be used to open the lock while in 
Shelved Mode. The correct opening procedure for a shelved lock is:

1.  Press * Key 

 EC

  Press * key until the letters EC (Enter Combination) appear in the display 

window.

2.  EC 

 Enter Shelved Mode Combination 

 OPn

  Enter the current Shelved Mode combination, whether it be the Factory 

  Combination of 50-25-50 or a new Shelved Mode combination, by sequentially

 

pressing those digits on the lock keypad. The lock will display the numbers as 

 

the combination is entered. When the combination has been correctly

  entered, the bolt will begin moving to open the lock and the lock will display “---” 

while the bolt is moving. The bolt will stop moving when it reaches the

  open position and the lock will display OPn. The lock will proceed from OPn to 

  CLo steps automatically if the lock bolt works hasn’t been retracted

 

within the OPn timeout.

3. OPn 

 Retract Bolt

 

Rotate the container handle to to unlock the lock, and the lock display will 

 

be cleared.

4.  Open Container Door

5.  Close Container Door

6.  Extend Bolt 

 CLo Rotate the container handle to extend the bolt. The lock will 

  display “---” while the bolt is moving. The bolt will stop moving when it

  reaches the closed position and the lock will display CLo.

Summary of Contents for Cencon MDB 30N


















Reviews: