background image

13

Query the Lock via Keypad

The Gen2 lock allows the user to gather information in the ield simply by pressing 
keypad commands, sometimes presenting their user key, and then reading the LCD.

DISPLAY LOCK LEVEL (#1)

It is sometimes necessary to determine the code level of the Cencon Lock with 
which you are working. This can be done through the keypad with the level displayed 
on the LCD. Use the following procedure:

1.  Press * Key 

 EC

Press * key until the letters EC (Enter Combination) appear in the display window.
“ Enter the 

#1

 keypad command.

2.  All Gen2 locks will display “

LL-

” , “

G 2

”, followed by 4 sets of 3 numbers, 

followed by “

HL-

” with 2 number pairs. If the LCD instead shows the letters 

LL-

” followed by a string of number pairs then “

HL-

” followed by 2 number 

pairs, then this lock is a Gen1 lock.

DISPLAY SERIAL NUMBER (#2)

The Gen2 lock’s Serial Number is a 9-digit number. To display the Lock Serial 
Number, press “

#

” and then “

2

” when “

EC

” is displayed.

Until a time when the irst 3 digits of the 9-digit serial number are non-zero, the lock 
will only display 6 digits. The Gen2 Cencon lock will display a series of two or three 
3-digit numbers, depending on what the value of the irst three numbers of the  
serial number are. When taken together, this series of numbers is the serial number 
of the lock. 

Example 1: Gen 2 Serial Number (9 digits with first 3 digits “000”)

 

Serial number of the lock is “000023456”
The lock will display “

Sn-

” followed by a series of two 3-digit numbers: “

023

” “

456

” 

Example 2: Gen 2 Serial Number (9 digits with first 3 digits non-zero)

Serial number of the lock is “001348729”
The lock will display “

Sn-

” followed by a series of three 3-digit numbers: “

001

”  

348

” “

729

” 

 

DISPLAY TOTAL AUDIT COUNT (#3)

The lock always keeps track of how many times it has been opened (Total Audit 
Count) no matter in which mode the opening occurred, including Shelved Mode, 
FLM, Route, and Bank. To learn the Total Audit Count, press the pound symbol, “

#

,” 

followed by the “

3

” whenever “

EC

” is displayed on the LCD. The display will lash 

two sets of numbers alternately on the screen. When taken as one four-digit number, 
this represents the Total Audit Count. For instance, if the LCD lashes “

AC-

” then 

“00” followed by “07,” the lock has a Total Audit Count of “0007,” meaning the lock 
has been opened seven times in all modes combined. This display can be cancelled 
by pressing the asterisk (*) button. The Total Audit Count does not reset when the 
lock is shelved. Once the counter exceeds 9999 openings, the Gen2 lock begins 
displaying more digits.

DISPLAY INTERNAL GMT (UTC) DATE/TIME (#71)

The UTC/GMT date and time are initialized in a Gen2 lock at the time of manufacture 
at Kaba Mas. When #71 is pressed, the current lock date & time are displayed. This 
display can be canceled by pressing the asterisk (*) key, or it will automatically be 
canceled when the lock powers down.

Summary of Contents for Cencon MDB 30N


















Reviews: