background image

User manual

Safety and the environment

Kaba digital cylinder 

k1evo805en-2012-09

7

2

Safety and the environment

2.1

Proper use

The digital cylinder is intended for use in building doors that are equipped with a lock and 
door furniture (see 3.4 Technical specifications on page 11). 

When using it in fire protection doors, escape routes or rescue routes, the locally applicable 
guidelines and building regulations must be observed.

2.2

Safety indications for this product

2.2.1 Handling of lithium batteries

WARNING

Risk of personal injury or death.

Incorrectly used or installed digital cylinders prevent emergency exit closures or 
panic closures from opening.

Risk of explosion

Lithium batteries can explode or burst explosively. Improper handling of 
lithium batteries can lead to fires and explosions.

Follow the instructions below:

• Only replace lithium batteries by batteries of the same type.

• Do not open, drill through or squash lithium batteries.

• Do not burn lithium batteries or expose them to high temperatures.

• Do not short circuit lithium batteries.

• Do not recharge lithium batteries. 

• Do not connect lithium batteries in parallel. 

Summary of Contents for 1434LEA
















































Reviews: