background image

LOCK OPERATION & RESPONSES

•   To “power” a self-powered lock, turn the dial back 

4

4

4

4

4

 and forth 

3

3

3

3

3

 in both

directions.

•   The lock is “powered” when simultaneous green 

G

 and red 

R

 flashes

display with a beep 

8

8

8

8

8

.

•   Each keystroke generates a green flash 

G

 with a beep 

8

8

8

8

8

.

•   To cancel entry, press 

.

•   The completion of a step within an operation is indicated by a green flash 

G

with a beep 

8

8

8

8

8

.

•   The successful completion of an operation is indicated by simultaneous

green 

G

 and red 

R

 flashes. 

On a Battery powered lock, there will also be

a beep 

8

8

8

8

8

 .

•   An error is indicated by three red flashes with beeps. 

R

 

8

8

8

8

8

 

 

R

 

8

8

8

8

8

 

 

R

 

8

8

8

8

8

•   On a Battery powered lock, a Low Battery Condition is indicated by rapidly

alternating green 

G

 and red 

R

 flashes at the time the lock is opened.

OPEN/CLOSE THE CONTAINER

1.

For self-powered lock, power  

4

4

4

4

4

 

3

3

3

3

3

 the lock 

G

 

R

 

8

8

8

8

8

2.

Position the dial to cover the red bar.

3.

•  

For Single Mode  

EEEEE

 

  

(Factory combination is “

50 25 50

”.)

    Enter Manager User (User 1) or User 2 combination. 

G

 

8

8

8

8

8

•  

For Dual Custody Mode    

EEEEE

 

EEEEE

    Enter User 1 or User 2 combination. 

G

 

8

8

8

8

8

    Enter the second combination. 

G

 

8

8

8

8

8

Wrong Try Penalty:  5 wrong tries =

     

3 min. lockout  (Timed only while lock is powered.)

Each additional wrong try = 3 min. lockout

Red flashes

 

with beeps

 

R

 

8

8

8

8

8

 

will occur during the lockout while lock is powered.

4.

•  

 For Slide Bolt

immediately rotate the container handle 

to retract bolt

works

 before green 

G

 and red 

R

 lights flash

. Open the container door. To

close and lock the container, close the door and rotate the container handle back
to locked position.

•   

For Dead Bolt or Spring Bolt

immediately turn the dial to the right 

3

3

3

3

3

 to

retract the bolt

 before green 

G

 and red 

R

 lights flash

 and open the con-

tainer door.  To close and lock the container, close the door.  

For Dead Bolt

, you

must also turn the dial to the left 

4

4

4

4

4

 until the bolt is fully extended.

Summary of Contents for 52









Reviews: