Kaba E-730 Series, Installation Manual

8

E-730/630/750/79E/ RT Series Installation Guide - PK3677_T_04_16

Activate the panic bar. The latch bolt or rod 

retracts fully.

Turn the outside lever downward. The latch bolt 

or rod does not retract.
If the latch bolt or rod retracts, verify that 

the batteries are properly installed.
If the lever feels tight (hard to turn, or does 

not return easily to its horizontal rest position), 

check the spindle length vs. the door thickness 

(the spindle may be too long). Check that the 

slotted end of the spindle is inserted in the lock 

housing hub, not the exit device.

Test the lock’s response to keycards: a Test key-

card, a Grand Master keycard, and an Emergency 

keycard. 
Insert keycards as shown below, with the mag-

netic stripe facing toward the door and to the 

left. For 79E, present cards to reader.

A  Test the Lock Before Programming

Normal Entry: Use the Test keycard with the 

reader. The 

red

 and 

green

 LEDs each flash once 

and then the 

green

 LED flashes for four sec-

onds. 
Turn the outside lever downward while the 

green

 LED is flashing. The latch or rod retracts 

fully. Release the lever, then turn it again. The 

latch or rod must not retract after the LED 

stops flashing without first inserting the 

keycard .

B  Lock Programming

Program the lock with its Common Area number 

(exit devices are usually programmed as common 

areas, see Reference Manual).
Use the Grand Master keycard with the reader. 

The 

green

 LED flashes. Turn the outside lever 

downward while the 

green

 LED is flashing. The 

latch or rod retracts fully and the LED stops 

flashing after 4 seconds. Release the lever, 

then turn it again. The latch or rod must not 

retract again without first inserting the 

keycard .

C  Emergency Keycard Access

Use the Emergency keycard with the reader. 

The 

green

 LED flashes for 4  seconds. Then, turn 

the outside lever downward. The latch or rod 

retracts fully .

While standing outside the room, close the door 

and ensure that it is  properly latched. Open the 

door using the Grand Master keycard using the 

same procedure.

Caution! Perform the following procedures 

in order, with the door OPEN unless other-

wise indicated.

!

FDU

Program the lock using the FDU and the 

E-760/770/790 communication cable (see 

Reference Manual). If this is not a new installation 

but a replacement of a single lock or a group of 

locks in a property already equipped with the Kaba 

Locking system, transfer the security informa-

tion from a neighbouring lock to the new lock by 

using the Reset Addresses function (see Reference 

Manual resetting lock addresses). 

ATLAS

Program the lock using the M-Unit (Maintenance 

Unit). Refer to ATLAS User Guide.

I

n the case of a replacement lock resetting the 

addresses will ensure that all past lost and stolen 

keycards remain cancelled in the new lock and will 

set the addresses for the Section, Floor, Group, 

Zone and Area sub-master level so that staff key-

cards in use at the property will have the same 

pattern of access to the door as before. This step 

makes the lock replacement transparent so that 

the new lock accepts and rejects the same key-

cards as the old lock.

Multihousing

Program the lock using the M-unit or EAMU FDU.. 

Refer to RezShield User Guide or FDU user Guide.

1

  Panic Bar

2

  Outside Lever

3

  Electronics and Card Reader

E 

 TEST THE OPERATION OF THE E-730/750/79E LOCK

(For 630 lock go to Section H) (For RT lock series, please refer to system 6000 manual)

F 

 PROGRAM THE E-730/750/79E LOCK

(For 630 lock go to Section H) (For RT lock series, please refer to system 6000 manual)