Kaba E-Plex 30 Series, Operation Manual

28

The following procedure applies to the E-Plex 30xx locks only:

PROCEDURE 19 - SWINGBOLT OPERATION

This ope 4.ration is similar to the 4. Privacy function of a conve 4.ntional lock with a 
physical de 4.adbolt, but not quite 4.!  In the 4. E-Ple 4.x 3000 Swinbolt ope 4.ration, any 
valid use 4.r can dise 4.ngage 4., ie 4. ., ove 4.rride 4. the 4. “privacy” by e 4.nte 4.ring a valid PIN and 
the 4.n turning the 4. thumbturn which will re 4.tract the 4. swingbolt down . Now the 4. lock 
will be 4.have 4. as though it is in a “latch holdback” mode 4. since 4. the 4. swingbolt is 
comple 4.te 4.ly re 4.tracte 4.d and stays re 4.tracte 4.d, thus allowing fre 4.e 4. acce 4.ss without any 
code 4.s . You pe 4.rform the 4. same 4. se 4.que 4.nce 4. of ope 4.rations to e 4.ngage 4., ie 4. ., re 4.-lock by 
bringing the 4. swingbolt back to its “home 4.” (horizontal locke 4.d) position .
• 

 the 4. swingbolt e 4.ngage 4. (proje 4.ct it) and dise 4.ngage 4. (re 4.tract it) actions are 4. 
strictly manual by flipping the 4. thumbturn on the 4. lock front housing . This 
function is ne 4.ithe 4.r programmable 4. nor automatic and so you must e 4.nsure 4. 
to re 4.-lock if it was le 4.ft too long in a re 4.tracte 4.d position,

• 

 any valid use 4.r can pe 4.rform this  function – ie 4. ., e 4.ngage 4. or dise 4.ngage 4. the 4. 
swingbolt anytime 4.,

• 

 whe 4.n the 4. swingbolt is dise 4.ngage 4.d (re 4.tracte 4.d), it will physically stay  
re 4.tracte 4.d down whe 4.n the 4. door close 4.s so that use 4.rs carrying package 4.s e 4.tc 
do not have 4. the 4. inconve 4.nie 4.nce 4. of having to turn the 4. thumbturn again to 
ope 4.n the 4. door, but simply push the 4. door to e 4.nte 4.r without a code 4.,

• 

 from the 4. inte 4.rior side 4. of the 4. door, any pe 4.rson (valid use 4.r or not) can  
manually re 4.tract or e 4.ngage 4. the 4.  swingbolt to unlock or lock the 4. door .

Required User Level:  Master, Manager, Access user & Service user

1 .   

To Disengage (retract swingbolt)

: Ente 4.r a valid PIN to ope 4.n and the 4. lock will 

flash the 4. gre 4.e 4.n LED indicating that you are 4. a valid use 4.r and you are 4. allowe 4.d 
to dise 4.ngage 4. the 4. swingbolt to unlock . Turn the 4. thumbturn on the 4. lock front 
housing clockwise 4. and hold . The 4. swingbolt will fully re 4.tract down and will 
stay re 4.tracte 4.d, allowing you to e 4.nte 4.r the 4. door . Le 4.t go off the 4. thumbturn so 
that it will re 4.ve 4.rt back to its normal horizontal (home 4.) position but the 4. swing-
bolt will stay re 4.tracte 4.d and dise 4.ngage 4.d .

2 .  You can 

also

 dise 4.ngage 4. the 4. swingbolt using the 4. 

mechanical override key

 by 

pe 4.rforming the 4. following ope 4.ration: inse 4.rt the 4. me 4.chanical ke 4.y in the 4. lock 
ove 4.rride 4. cylinde 4.r’s ve 4.rtical slit and turn it clockwise 4. to the 4. horizontal position . 

With the key still in this horizontal position

, turn the 4. thumbturn clockwise 4. 

to dise 4.ngage 4. the 4. swingbolt which will fully re 4.tract down and will stay re 4.tract-
e 4.d . Le 4.t go off the 4. thumbturn so that it will re 4.ve 4.rt back to its normal horizon- 
tal (home 4.) position . Turn the 4. ke 4.y back to its ve 4.rtical position and re 4.move 4. it 
from the 4. lock cylinde 4.r .

3 .  

To Engage (project swingbolt)

: This proce 4.dure 4. is almost the 4. same 4. as in Ste 4.p 

1 above 4. . Ente 4.r a valid PIN and the 4. lock will flash the 4. gre 4.e 4.n LED indicating that 
you are 4. a valid use 4.r and you are 4. allowe 4.d to e 4.ngage 4. the 4. swingbolt to lock 
back . Turn the 4. thumbturn on the 4. lock front housing clockwise 4. and hold . The 4. 
swingbolt will re 4.ve 4.rt back up to its locke 4.d, horizontal (home 4.) position . Le 4.t go 
off the 4. thumbturn so that it will also re 4.ve 4.rt back to its normal horizontal 
(home 4.) position .