background image

K

A

B

A

A

C

C

E

S

S

C

O

N

T

R

O

L

2

9

4

1

IN

D

IA

N

A

A

V

E

N

U

E

W

IN

S

T

O

N

-S

A

L

E

M

,

N

C

2

7

19

9

-3

7

7

0

N

O

P

O

S

T

A

G

E

N

E

C

E

S

S

A

R

Y

IF

M

A

IL

E

D

IN

T

H

E

U

N

IT

E

D

S

T

A

T

E

S

B

U

S

I

N

E

S

S

R

E

P

L

Y

M

A

IL

F

IR

S

T

-C

L

A

S

S

M

A

IL

P

E

R

M

IT

N

O

.

15

6

3

P

O

S

T

A

G

E

W

IL

L

B

E

P

A

ID

B

Y

A

D

D

R

E

S

S

E

E

W

IN

S

T

O

N

-S

A

L

E

M

,

N

C

Kaba Access Control warrants this product to be free from defects in

material and workmanship under normal use and service for a period

of three (3) years. Kaba Access Control will repair or replace, at our

discretion, 5000 Series Locks found by Kaba Access Control analysis

to be defective during this period. Our only liability, whether in tort or

in contract, under this warranty is to repair or replace products that are

returned to Kaba Access Control within the three (3) year warranty

period.

This warranty is in lieu of and not in addition to any other warranty or

condition, express or implied, including without limitation merchantabil-

ity, fitness for purpose or absence of latent defects.

ATTENTION: This warranty does not cover problems arising out of

improper installation, neglect or misuse. All warranties implied or

written will be null and void if the lock is not installed properly and / or

if any supplied component part is substituted with a foreign part. If the

lock is used with a wall bumper, the warranty is null and void. If a

doorstop is required, we recommend the use of a floor secured stop.

The environment and conditions of use determine the life of finishes

on Kaba Access Control products. Finishes on Kaba Access Control

products are subject to change due to wear and environmental

corrosion. Kaba Access Control cannot be held responsible for the

deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval.

Approvals and Returned Goods Authorization Numbers (RGA Numbers)

for the 5000 Series are available through our Customer Service

department in Winston-Salem, NC (800) 849-8324.

The serial number

of a lock is required to obtain this RGA Number

. The issuance of an

RGA does not imply that a credit or replacement will be issued.

The RGA number must be included on the address label when material

is returned to the factory. All component parts including latches and

strikes (even if not inoperative) must be included in the package with

return. All merchandise must be returned prepaid and properly pack-

aged to the address indicated.

* Simplex 5000 locks are warranted three (3) years from date of

purchase. E-Plex 5x00 locks are warranted three (3) years from

date of activation.

KABA E-PLEX

®

5x00 SERIES

LIMITED WARRANTY

Summary of Contents for E-Plex 5x63











Reviews: