Kaba ILCO FDU User Manual Download | Manualshive

Page: 137 / 276

background image

Chapter 4

126

Kaba Ilco Lodging Access Control System

E. Reset Keycards

E.1 Guest Reset

E.2 Adjoining Suite Reset

E.3 Common Door Suite Reset

E.4 One-Shot Reset

Purpose:

Invalidates the corresponding room or suite entry keycard.

The Reset keycard must be inserted in all locks leading to the specified guest room
or suite.

Once done, all entry keycards for the same level encoded before the Reset

keycard was encoded will be denied entry in the lock.

Example:

(i)

Suppose that one of the rooms in an Adjoining Suite is to be dropped from the
reservation but that the guests require continued access to the remaining rooms of
the Adjoining Suite. Access to the room being dropped from the reservation can
be revoked by inserting a valid Adjoining Suite Reset keycard in the lock for the
affected room. Alternatively, a valid Group Lockout keycard can be inserted in
the affected lock

(see Section 3.10 part C.5 – Group Lockout).

(ii)

Suppose that a guest has lost their keycard and is away from the property. To
cancel their lost keycard without giving access to the room and without encoding
a new keycard until they return, the corresponding Reset keycard should be
encoded and inserted in the lock to the guest's room.

Minimum keycard:

Front Desk Authorization

Shortcut:

For Guest Reset: Swipe authorized keycard, press 5, 1 and 1

For Adjoining Suite Reset: Swipe authorized keycard, press 5, 1 and 2

For Common Door Suite Reset: Swipe authorized keycard, press 5, 1 and 3

For One-Shot Reset: Swipe authorized keycard, press 5, 1 and 4

Expiry:

From 1 to 24 hours

Factory default expiry:

24 hours

Parameters:

Room/Suite number(s)

Number of cards

Options: None

E.5 Convention Suite Reset

Purpose:

Assigns a Convention Address to a group of guest rooms. Once the Convention Suite
Reset keycard has been inserted in all doors, the doors will accept a Convention Suite
keycard with the same address number, as long as the Convention Suite keycard was
encoded

after

the Convention Suite Reset keycard.

«
...
135
136
137
138
139
...
»

Summary of Contents for ILCO FDU





















































































































































































































































































Reviews:

No comments

Related manuals for ILCO FDU

Brand: ABATEC Pages: 8

Brand: Salda Pages: 16

Brand: Radware Pages: 98

Brand: RadioMaster Pages: 10

Brand: Rain Bird Pages: 18

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brand: ROBOT3T Pages: 21

Brand: StudioComm Pages: 61

Brand: Danfoss Pages: 14

Brand: Invacare Pages: 44

AMP 3K/40 CE 2161600-1

Brand: TE Connectivity Pages: 29

Brand: C-TEC Pages: 42

Brand: National Instruments Pages: 3

Brand: Kelly Pages: 43

Brand: Niko Pages: 80

Brand: X10 Pages: 3

Boiler Control TSBC

Brand: Thermal Solutions Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands