background image

PK3520_09_07 • REMOTE ACCESS CONTROLLER - 660G XT

3

1.0  Introduction and Disclaimers

Target Audience

Please read and follow all directions carefully. These instructions 

are designed for use by lock installers or anyone who is familiar 

with common safety practices and competent to perform the 

steps described herein. 

For  a  typical  installation,  no  professional  electrician  is  required 

because the 660G XT is a low voltage installation system. 

Kaba  Lodging  Systems  is  not  responsible  for  damage  or 

malfunction due to incorrect installation.

Safety Procedures

Installation is to be done following standard safety procedures 

with  adequate  equipment  prescribed  herein  and  wearing 

adequate protection for body safety. Power is to be off during 

the  installation  process  as  well  as  for  any  maintenance 

procedures.

Technical Assistance

For technical assistance call  

1-800-906-4526

OR

Visit the Kaba Support Website:

http://connect.kabalodging.com

Warnings and Cautions

Please read and follow all directions  
carefully.

!

Important: Carefully inspect windows, doorframe, door, 
etc. to ensure that the recommended procedures will not 
cause damage. Kaba Ilco’s standard warranty does not 
cover damages caused by installation.

!

Important: The RAC 660G should always be installed in a 
secured room or facility with controlled access to prevent 
access to the system.

!

Caution: Wear safety glasses when making  
the holes.

!

 

2.0  Product Description

2.1  Features

The  660G  XT  is  designed  to  operate  electrical  locking  or 
control  devices  where  a  stand-alone  electronic  lock  is  not 
practical. The system 

can control any door or access point 

from up to 100 feet

 (30 m) away. The 2x6 Keypad can be 

mounted directly on door frames, while the 3x4 keypad is wall 
mounted.

The  660G  XT  is  an  access  control  solution  that  provides  a 
single relay output, up to 2 keypads, a battery back-up option, 
and much more as per the feature list on page 3. See figure 1 
for a typical configuration.

Figure 1

Power Adapter

Keypad

Ingress

Keypad

Egress

Keypad

RAC 660G

RAC 660G XT

Up to 2

Keypads

Battery Back-up

Power Adapter

Summary of Contents for ILCO RAC 660G XT























Reviews: