17
Change PIN
Note: This operation is only applicable if PIN length is not 0. Master User, Man-
ager User, and Access User PINs can be changed, but a Service User PIN can-
not be changed. An Access User’s PIN may only be changed if the user is
enabled and is not currently restricted from access to the lock for any reason.
The default PIN for an Access User is all 0’s and must be changed before the
lock will open.
Step
Detailed Instructions
1.
Power lock.
Power the lock by depressing the outside lever.
2.
Enter Master User,
Enter the user’s current combination. The lock will
Manager User or
beep/flash the green LED on each keystroke
Access User
entered. If the
Clear key is pressed during data
combination
entry, the lock responds with one beep/flash of the
green LED followed by the red LED, and all digits of
the combination must be re-entered. The lock
responds with three beeps/flashes of the green LED
to indicate available entry. If the combination is not
valid, the lock responds with three beeps/flashes of
the red LED.
3.
Press then 5.
Before re-lock time expires, press (Enter key)
followed by the 5 key. The lock responds with two
beeps/flashes of the green LED.
4.
Enter new
Enter the new combination (User ID + new PIN).
combination (User
The lock responds with two beeps/flashes of the
ID + new PIN)
green LED if the combination was verified
successfully. The lock responds with two beeps/
flashes of the red LED to indicate an error.
5.
Enter new
Enter the new combination (User ID + new PIN)
combination (User
again for verification. The lock responds with two
ID + new PIN)
simultaneous beeps/flashes of the green and red
again.
LEDs if the combination was verified success
fully. The lock responds with two beeps/flashes of
the red LED to indicate an error.
The new PIN is now active for the user.
16
Add Access User(s)
Note: If at any time during the procedure the lock power drops below a
sufficient level for operation, the lock will continually beep and flash the red
LED, prompting the user to depress the outside lever to provide additional
power within 5 seconds.
Step
Detailed Instructions
1.
Power lock.
Power the lock by depressing the outside lever.
2.
Enter Master User
Enter the Master User or Manager User combina-
or Manager User
tion. The lock will beep/flash the green LED on each
combination
keystroke entered. If the Clear key is pressed during
data entry, the lock responds with one beep/ flash of
the green LED followed by the red LED, and all dig-
its of the combination must be re-entered. The lock
responds with three beeps/flashes of the green LED
to indicate available entry. If the combination is not
valid, the lock responds with three beeps/flashes of
the red LED.
3.
Press then 2.
Before re-lock time expires, press (Enter key)
followed by the 2 key. The lock responds with two
beeps/flashes of the green LED.
4.
Enter Access
Enter a User ID for an Access User. The lock
User ID.
responds with two beeps/flashes of the green LED.
5.
Enter Access
Enter the Access User ID again for verification. The
ID User again.
lock responds with four beeps/flashes of the green
LED. The lock responds with two beeps/flashes of
the red LED if the User ID was unconfirmed or no
space was found in the Access User table.
The Access User is now added to the lock with
the specified User ID and a default PIN of all 0’s
if PIN length is not 0.
6.
Repeat Steps 4
If additional Access Users are to be added, repeat
and 5 to add
Steps 4 and 5 until all Access Users have been
more users or
added. If no additional Access Users are to be
go to Step 7.
added, go to Step 7.
Caution: If you are adding multiple Access Users, you may need to depress the
outside lever at this time to provide additional power.
7.
Press .
Press (Enter key) to exit. The lock responds
with two simultaneous beeps/flashes of the green
and red LEDs and exits this procedure.
