background image

19

O-3

Resetting and Recovery of Current Combination

To reset the code gears (a), each one of the 5 “L” shaped

legs (b) of the unlocking slide (c) must engage snugly

with the corresponding code gear pocket (d) next to it.

Position the chamber in one hand, as

shown. Hold chamber by the top screw tab

(e) and bottom screw tab (f).

Rotate the reset cam (g) back toward you

with your finger, towards the key stems (h) as far as it will

go and then release. Now look at the code gears (a) and

the unlocking slide (c). Note that some or all 5 of the code

gear pockets (d) are rotated away from the “L” shaped

legs (b) as if out of alignment. Typically each code gear

pocket will be at a slightly different distance compared to

the other.

Note:

Sometimes

two different

gear pockets are away from alignment

by

exactly the same distance

– this indicates that the current combination uses

two different number buttons

(example, 2 and 4)

depressed at the same

time

as part of the combination.

Using a small flat blade screw driver or your thumbnail, depress the key

stem which corresponds to the gear pocket which has been rotated the

farthest away

(out of alignment) from the “L” shaped leg. When

depressed, the key stem(s) should stay down and the corresponding

gear pocket(s) should move closer to its corresponding “L” leg, closer to

alignment. Record the key stem number. This is the

first

number of your

combination.

Note:

If two gear pockets are at the

same distance

, depress

both

of these corresponding key stems

at the same time

.

Continue by pressing the key stem that corresponds to the gear pocket

that was the

next furthest away

(do not include gear pockets that have

already been rotated). Record each key stem number that is depressed.

Continue this procedure until all five gear pockets are aligned with their

corresponding “L” shaped legs on the unlocking slide. The combination

is the recorded numbers, in the order recorded.

Note:

If you depress the wrong key stem by mistake, rotate the reset cam

back toward you, (toward the key stems and release). This resets the code

gears and you must repeat the above procedure, O-3.

a

c

j

b

d

i

a

c

f

j

g

h

e

Summary of Contents for SIMPLEX 5000 CYLINDRICAL

























Reviews: