background image

KABA SIMPLEX

®

/E-PLEX

®

5x00 SERIES

LIMITED WARRANTY

Kaba Access Control warrants this product to be free from defects in material

and workmanship under normal use and service for a period of three (3) years.

Kaba Access Control will repair or replace, at our discretion, 5000 Series Locks

found by Kaba Access Control analysis to be defective during this period. Our

only liability, whether in tort or in contract, under this warranty is to repair or

replace products that are returned to Kaba Access Control within the three (3)

year warranty period.

This warranty is in lieu of and not in addition to any other warranty or

condition, express or implied, including without limitation merchantability,

fitness for purpose or absence of latent defects.

ATTENTION: This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and / or if any supplied component part

is substituted with a foreign part. If the lock is used with a wall bumper, the

warranty is null and void. If a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes

on Kaba Access Control products. Finishes on Kaba Access Control products

are subject to change due to wear and environmental corrosion. Kaba Access

Control cannot be held responsible for the

deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization Numbers (RGA Numbers) for the 5000

Series are available through our Customer Service department in Winston-

Salem, NC (800) 849-8324.

The serial number of a lock is required to obtain

this RGA Number

. The issuance of an RGA does not imply that a credit or

replacement will be issued.

The RGA number must be included on the address label when material

is returned to the factory. All component parts including latches and strikes

(even if not inoperative) must be included in the package with return. All

merchandise must be returned prepaid and properly packaged

to the address indicated.

K

A

B

A

A

C

C

E

S

S

C

O

N

T

R

O

L

2

9

4

1

IN

D

IA

N

A

A

V

E

N

U

E

W

IN

S

T

O

N

-S

A

L

E

M

,

N

C

2

7

19

9

-3

7

7

0

NO

PO

S

T

A

GE

NE

CE

S

S

AR

Y

IF

MAILED

IN

THE

UNITED

S

T

A

TE

S

B

U

S

I

N

E

S

S

R

E

P

L

Y

M

A

IL

F

IR

S

T

-C

L

A

S

S

M

A

IL

P

E

R

M

IT

N

O

.

15

6

3

P

O

S

T

AG

E

W

IL

L

B

E

P

A

ID

B

Y

A

D

D

R

E

S

S

E

E

W

IN

S

T

O

N

-S

A

L

E

M

,

N

C

Summary of Contents for Simplex 5000 Series













Reviews: