background image

hy-switch for KACO blueplanet hybrid inverters

 

Page 13

 

 

 

5.

 

Technical data 

5.1.

 

Electrical data 

 

isolator switch 

hy-switch 

Max. isolation voltage 

264 V 

Max. load current 

50 A 

Max. continuous power 

30 000 W 

Grid failure detection 

200 ms 

Switchover time from grid to standalone mode  < 3 s (depending on test sequence) 

Current counter 

Measuring range of internal current sensors 

35 A RMS 

Measuring range of external current sensors 

70 A RMS 

Measuring accuracy of AC power (internal) 

3% 

Measuring accuracy of AC power (external) 

5% 

Measuring speed 

Real-time 

Installation 

Max. cable length to the blueplanet hy-switch 

20 m 

AC cable cross-section max. 

35 mm² 

Communications connection 

1 x RJ45 (RS485) 

Connection for external current sensors 

3 x 3.5 mm jack 

General data 

Protection rating (IEC 60529) 

IP20 

Protection class (IEC 62109-1) 

Certificates 

VDE 0126, VDE AR-N 4105 

Warranty 

2 years 

Dimensions (W x H x D) 

170 x 280 x 92 mm 

Weight 

1.2 kg 

Supported devices 

Inverter 

blueplanet hybrid 10.0 TL3 

Max. number of inverters 

Tab. 1 Technical data 

 

5.2.

 

Environmental data 

 

 

blueplanet hy-switch 

Ambient temperature 

+5°C + 40°C 

Protection rating (KACO installation location) 

IP20 

Humidity range (non-condensing) [%] 

0 to 90 % 

Tab. 2 Environmental data 

Summary of Contents for blueplanet hy-switch





































Reviews: