background image

Operating Instructions Powador-proLOG_EN                                                 

Page 15

5.4.8  Digital output D0

The digital output can be used as an alarm output to control 
signalling devices or as a pulse output to connect a display.

Powador-proLOG M/XL 

Powador-proLOG S

Connecting a display to D0

Connecting a signalling device to D0

5.4.9 Analogue/digital 

inputs

The  unit  is  equipped  with  four  (XL)  or  one  (S,  M)  analogue 
input(s), which are designed for a voltage measurement of 0 
to 10 V.

Powador-proLOG XL  

Powador-proLOG S

Counter pulses (maximum frequency: 14 Hz) can be recorded 
using four (XL) or one (S, M) digital counter input(s). An inter-
face in accordance with the S0 specifi cation must be available.

Powador-proLOG XL  

Powador-proLOG S

S e c t i o n   5   ·  

I n s t a l l a t i o n

NOTE

To confi gure this function, connect to the Powador-pro-
LOG and make the required settings via -> “Admin moni-
toring > Switching output” in your browser.

ATTENTION

The  output  is  designed  as  an  optocoupler  output  (N/O 
contact) and must therefore be connected to an external 
voltage supply, if necessary. The maximum load is 50 mA.

NOTE

The analogue inputs can be optionally converted for
current measurement or resistance measurement.
You do this in the confi guration menu of the Powador-
proLOG (Admin-Messung -> Admin measurement > Ana-
logue channels).

ATTENTION

Incorrect polarity or using an external voltage supply 
greater than 24 V can destroy the measuring input. The 
24-V supply is available starting at terminal DI+.

ATTENTION

Incorrect polarity or using a voltage supply greater than 
12 V can destroy the measuring input.

NOTE

The digital inputs can be optionally converted for status 
evaluation.
This means that the Powador-proLOG can evaluate 
switching states 0 or 1 (N/C or N/O contact).
This must be set up using the confi guration fi les
for the Powador-proLOG.
Please contact the KACO new energy hotline.

Powador-

pro

LOG

+ -

D0
+ - 

 24V 
+     - 

Signalgeber 

Powador-proLOG

Impulseingang 

Anzeigedisplay 

Powador-

pro

LOG

D0
+ - 

+ -

Powador-proLOG

Display

Summary of Contents for Powador-proLOG

















































Reviews: