background image

3. Shut down the machine.
4. Wait until the machine has automatically vented.

Pressure gauge reads 0 bar.

5. Open the outlet valves.
6. Check the oil level after about 5 minutes.

Top up if necessary.

7. Carry out a visual check for leaks.

10.4.5  Changing the oil separator cartridge

The oil separator cartridge cannot be cleaned.
The life of the oil separator cartridge is influenced by:

■ Contamination in the air drawn into the compressor
■ and adherence to the changing intervals for:

─ Cooling oil
─ Oil filter
─ Air filter

Material Spares

Cleaning cloths

Precondition The machine is shut down.

The machine is fully vented, the pressure gauge reads 0 bar.
Machine cooled down.
All compressed air consumers are disconnected and the air outlet valves are open.
The negative cable to the battery is disconnected.

10 Maintenance

10.4 Compressor

No.: 9_9432 02 E

Service Manual    Screw Compressor  
M43  

93

RAMIRENT

Summary of Contents for M43























































































































































































































































Reviews: