background image

 

Address: 4 East Jiangcun Road, Henglin Town, Changzhou, Jiangsu 

Tel: 0086-519-88491333 

Fax: 0086-519-88496333 

3.2

 

Comparison Table of Electrical Performance and Appearance for Different Modes 

Mode 

KDDY008B KDDY008C KDDY001B 

KDDY001C 

Maximum Output Current 

 8A 

 5A 

 8A 

 5A 

Emergency Power Output 

 

 

 

 

Dimension(L*W*H) 128*58*38.2 128*58*38.2 138*83*38 138*83*38 

Power Wire 

NISPT-1/ 

Specified by clients 

NISPT-1/ 

Specified by clients 

NISPT-1/ 

Specified by clients 

NISPT-1/ 

Specified by clients 

 

1)

 

The switch power supply made by our company must not be used on terminals that do not 

obtain our approval or match 

our products. 

2)

 

It is normal that the switch power supply cabinet may heat during usage. 

4.

 

Installation and Usage of Switch Power Supply 

Cautions! 

Before installation, switch power supply must be powered off. After installation the power 

supply can be powered on. 

4.1

 

Connection of Switch Power Supply (See Figures 1a and 1b) 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

A. Remove lock nut 

B. Insert connector 

C. Tighten lock nut 

Figure 1a 

Lock up the connector to prevent dropping off.

Summary of Contents for KDDY001B













Reviews: